صفحة 1 من 2 1 2 الأخيرةالأخيرة
النتائج 1 إلى 15 من 22

الموضوع: تشريح الهارد ديسك

  1. #1
    عضو
    تاريخ التسجيل
    Jun 2005
    المشاركات
    60
    معدل تقييم المستوى
    0

    تشريح الهارد ديسك

    بسم الله الرحمن الرحيم




    مقدمة


    بفضل الله سنقوم بإلقاء نظرة سريعه على الهارد ديسك ومكوناته وبعض النصائح الهامة في

    الصيانة


    يتكون الهارد من جزأين أساسين

    1- البردة وهي : الجزء خارجي ويطلق عليه الدائرة

    المطبوعة(printed circuit board*pcb*) أو

    logic board


    2-الميديا وهي: الجزء الداخلي ويطلق عليه

    HDA إختصار لــــ Hard Drive

    Assembly


    كما توضح الصورة التاليه



    ميديا الهارد لا يمكن التعامل معها بسهولة كالبردة حيث أنها يتم تجميعها في غرف

    معقمة ولذا أي تلاعب فيها أو خطأ في فكها غالبا ما يؤدي لتلف الهارد لأن دخول

    أي ذرة غبار أو تراب ربما تؤدي لتلف الاسطوانات وسبب ذلك السرعه العالية التي

    يدور بها الموتور .

    لذلك لا توجد صيانة للميديا الا في بعض المكاتب المتقدمة والمجهزة بما يسمى

    clean room


    ........................

    التوصيلات Connectors


    تنقسم التوصيلات لأي هارد ديسك إلى قسمين

    1- وصلة الباور

    2-وصلة الداتا أو ما يسمى interface



    ويوجد ثلاث أنواع من وصلات الداتا

    1- ATA =Advanced Technology Attachment)

    SATA =Serial ATA -2

    SCSI -3 =Small Computer Systems Interface
    وهو منتشر في أجهزة السرفرات حيث السرعات العالية ونادرا ما نجده في الاجهزة العادية.

    النوع الأول الهاردات الداتا (ATA=PATA)



    The master/slave jumper on ATA hard drives can be configured in three

    different ways:

    [LIST][*] Master: this means that this drive will

    be the only one attached to the cable that connects the hard drive to the

    computer or will be the first drive in a two-drive configuration.[*] Slave: this means that this drive will be

    the second drive attached to the cable that connects the hard drive to

    the computer.[*] CS (Cable Select): this means that you

    will use a “special” cable (called CS cable) that the configuration of

    whether a drive will be master or slave will be made by the position of

    the hard drive on the[/LIST]

    النوع الثاني الساتا SATA






    .............

    الـبـردة=Logic Board


    غالبا ما سنجد من اربعة لخمس دوائر هي التي تتحكم في الهارد وفي الاجيال

    الحديثة كالعادة تم دمج بعض الدوائر داخل الشيب (البرسسور) نفسه وسأتناول

    لاحقا شرحها بالتفصيل ..

    مثال على البردة الداتا


    Logic board from an ATA hard drive

    مثال على البردة الساتا


    Logic board from a SATA hard drive

    أهم الدوائر الموجودة على البردة هي

    1- البرسسور(controller)
    هو الذي يتحكم في كل شيء على البردة مثال ذلك


    [LIST][*]نقل الداتا بين الهارد ديسك والكمبيوتر
    [*]يتحكم في المواتير الموجودة في الهارد ديسك
    [*]يوجة الهدود(رؤس الكتابة) من أجل أن تقوم بالكتابة والقراءة على الميديا
    [*]وغيرها الكثير من الوظائف[/LIST]


    2- أيسى السوفت وير "البيوس" Flash-

    ROM circuit


    وهي التي يتم تخزين عليها الفيرم وير الخاص بالهارد ويشمل هذا الفيرم وير

    التعليمات التي يقوم الكنترولر بتنفيذها بالاضافة لبعض اوامر البنية الهندسية التي تتشكل بها الميديا








    وفي الهاردات الحديثة يكون مدمج داخل الكنترولر كما توضح الصورة التالية




    3-أيسي بور الموتور

    نظرا لأن الكنترولر لا يستطيع أن يمد الموتور بالتيار الكافي لدورانة تم تعويض هذا

    الفقد بأيسي خاص لبور الموتور( motor driver chip) حيث تقوم تلك

    الشيب بتكبير التيار current amplifier

    وبالتالي فإنه أيس الموتور يتسلم الأمر من الكنترولر ويوصله للموتور بعد أن يتم

    تحميله بتيار عالي higher current ولهذا

    السبب فانها تقع بين الكنترولر والموتور.

    4-الـــــــــرام ( Random Access Memory (BUFFER

    ولها وظيفه محددة على الهارد فكلما كانت سعتها اكبر كلما كان نقل الداتا أسرع

    ويمكن معرفة السعه لها عن طريق قراءة الداتا عليها والذهاب لموقع الشركة المنتجة والبحث هناك بنفس الرقم

    5-SATA/ATA converter chip

    هذه الشيب كانت موجودة في بدايات ظهور هاردات الساتا والسبب في ذلك هو

    تحويل فائض انتاجهم من هاردات الداتا لساتا عن طريق وضع شيب

    (converter chip)

    ومن أشهر تلك الشيبات Marvell 88i8030

    ومع ذلك الهارد له شكل هارد الساتا وأداء هارد الدتا.

    ..................

    الموتور Spindle Motor



    the spindle motor rotates at 5,400 rpm, 7,200 rpm or even 10,000 rpm,

    depending on the drive. The faster this motor rotates, the faster data

    can be read from the platters. Hard drives targeted to laptops usually

    rotates at 4,200 rpm.
    .................

    داخل الميديا




    كما توضح الصورة مجموعة من الإسطوانات القابلة للكتابة والقراءة في نفس الوقت

    والهدود مثبتة معا في ذراع ولذا كل الهدود تتحرك معا.

    ويقوم الموتور والذي يسمى voice coil بتحريك الذراع وسبب تسمته

    voice coil
    لان فكرة عملة هي نفس فكرة عمل السماعات

    الملف داخل مجال ممغنط ناتج عن طريق مغناطيس قوي وعن طريق اتجاه التيار

    في الملف يتحرك الذراع من اتجاه لاخر وعلى مدى شدة التيار يصل الذراع

    لمسافة اكبر أو أقل



    يتبع

  2. #2
    عضو
    تاريخ التسجيل
    Jun 2005
    المشاركات
    60
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك

    البــــــــــردة

    مثال ذلك الهاردات الساتا الحديثة ساتا 2



    البلوك ديجرام (Circuit design of modern drives)



    وكما نلاحظ من الصورة فإن المخطط يعتمد على أربعة أنواع من الشيبات

    1-microcontroller

    وهي الشيب التي تتحكم في الهارد كله مثل الكتابة والقراءة حركة الموتور وغيرها

    2-Flash ROM chip

    تحتوي على الفيرم وير الخاص بالهارد وفي مثالنا هذا مدمجة داخل الكنترولر

    3-chip controlling the spindle motor and voice coil

    تتحكم في حركة الموتور واتجاه وسرعة الملف المحرك للذراع الحاملة لرؤوس الكتابة

    4-ROM chip used as a cache buffer

    الرام وقد شرحتها سابقا

    منهجية عمل البردة

    عندما يتم توصيل الفولت للبردة تتولد اشارة reset , وتقوم دائرة معينه خاصة

    باشارة reset بإرسالها الى الكنترولر الذي بدوره يقوم بتنفيذ البرنامج المحمل في

    الروم ويقوم الكنترولر بعمل التهيئة الذاتية ماسحا كل معلومات التشغيل السابقة

    في الذاكرة ويعيد برمجة كل الشيبات والكنترولات القابلة للبرمجة داخل الميديا.

    بعد ذلك يقوم الكنترولر بدفع اشارة نحو ايسي بور الموتور واذا تم تسلمها بنجاح

    ولم تقابل عائق او تلف في الايسي يبدأ الموتورفي الحركة .

    ثم تبدأ بعد ذلك المرحلة الثانية لعمل الفيرم وير حيث يقوم بعمل اختبار داخلي

    لكل من:

    الـــــــــــرام data buffer RAM


    disk microcontroller

    حالة إشارة الدخل بالنسبة للكنترولر

    ثم يبدأ الكنترولر في تحليل الموجات منتظر وصول الموتور لسرعتة المطلوبة

    وبمجرد وصولة للسرعة المطلوبة يبدأ الكنترولر فيالتعامل مع دائرة الحركة داخل

    الميديا محركا رؤوس القراءة إلى المنطقة التي تحتوي على فيرم وير الميديا (التراك

    zero) ناقلا تلك الداتا الى رام او بفر الهارد من اجل العمليات التالية.ثم يتحول

    الكنترولر لوضع الاستعداد منتظر الاوامر التي ستأتي من المعالج.


    HDD read/write channel consists of a preamplifier/commutator (located inside HDA), read circuit, write circuit and a synchronizing clock.
    Drive preamplifier has several channels, each being connected to its respective head. The channels are switched by signals from the drive’s microprocessor. Preamplifier also contains a recording current switch and recording error sensor, which emits an error signal if a short circuit or break occurs in a magnetic head.
    Integrated reading/writing channel operating in the recording mode receives data from disk controller simultaneously with the recording clock frequency, performs data encoding, precompensation and transfers the data to preamplifier for writing to a disk. In the reading mode signal from preamplifier/commutator is transmitted to the automatic control circuit and then passes a programmable filter, adaptive compensatory circuit and pulse detector while being converted into data pulses sent to the disk controller for decoding and transfer through an external interface.

    Disk controller is the most complicated drive component which determines the speed of data exchange between a HDD and HOST.
    Disk controller has four ports used for connection to a HOST, microcontroller, buffer RAM and data exchange channel between it and HDD. Disk controller is an automatic device driven by microcontroller; from HOST side only standard registers of task file are accessible. Disk controller is programmed at the initialization stage by microcontroller, during the procedure it sets up the data encoding methods, selects the polynomial method of error correction, defines flexible or hard partitioning into sectors, etc.
    Buffer manager is a functional part of disk controller governing the operations of buffer RAM. The capacity of the latter ranges in modern HDDs from 512 Kb to 8 Mb. Buffer manager splits the whole buffer RAM into separate sectioned buffers. Special registers accessible from microcontroller contain the initial addresses of those sectioned buffers. When HOST exchanges data with one of the buffers the read/write channel can exchange data with another buffer sector. Thus the system achieves multisequencing for the processes of data reading/writing from/to disk and data exchange with HOST.

    Spindle motor controller regulates the motion of a 3-phase motor. It is programmed by the drive microcontroller. There are three control modes of spindle motor operation: the start mode, acceleration mode and stable rotation mode. Let us review the start mode. At power-up a reset signal is sent to the control microprocessor which performs initialization programming internal registers of spindle motor controller for a start. Drive controller generates phase switching signals; the spindle motor at that rotates at low speed generating self-induced electromotive force. Drive controller detects EMF and notifies the microprocessor which uses that signal for rotation control. In the acceleration mode microprocessor speeds-up phase switching and measures the rotational speed of the spindle motor until the speed reaches its rated value. As soon as the rated rotational speed is reached the controller introduces stable rotational mode. In that mode microprocessor calculates the time required for one revolution of the spindle motor based on the phase signal and adjusts the rotational speed accordingly. After relocation of magnetic heads from the parking zone the drive electronics begins tracking the stability of rotation using servo marks.

    Voice coil controller generates the control current moving drive positioner and stabilizing it over a defined track. Current value is calculated by microcontroller on the basis of digital error signal for head position relatively to a track (Position Error Signal or PES). Current value in digital form is transmitted to CPU, the analogous signal thus received is enhanced and supplied to the voice coil.
    ................

    Firmware data

    أو كما تسمي معلومات

    الخدمة الدخليه في الهارد وهي هامة جدا للدائرة الداخليه في الميديا وينصح بها

    دوما ان تكون بعيدة عن المستخدمين

    تنقسم إلى

    [LIST][*]Servo information or servo fields[*] [*] Low-level format[*] [*] Resident firmware microcode (operational programs)[*] [*] Configuration tables and settings
    [*]Tables of defects[/LIST]


    للمزيد من المعلومات عنها في الإقتباس التالي
    Servo fields are necessary for operation of a servo system used by the driving assembly of magnetic heads in a HDD; they serve for heads’ positioning and keeping them precisely over a defined track. Servo fields are recorded during the manufacturing process to an already assembled HDA through special service openings in its case. The openings are subsequently closed with sticky labels that read: Warning! DO NOT OPEN. The recording is actually performed using drive’s own heads in a special high-precision instrument – servo writer. Relocation of heads’ positioner is achieved through a motion of a special pusher of the servo writer using steady steps much smaller than the intervals between tracks.

    Firmware (microcode) of the control microprocessor is a collection of programs required for operation of HDD components. Here belong the programs used for initial diagnostics, control of spindle motor rotation, data exchange with disk controller, buffer RAM, etc. In most HDD models firmware microcode is stored within internal microcontroller ROM; some models employ external Flash ROM. In some HDD models a part of firmware programs is recorded to magnetic disk in a special firmware zone while ROM contains the programs used for initialization, and positioning together with primary loader reading the firmware data from magnetic disk to RAM. Since actual firmware modules are first loaded to RAM before execution they have been called resident modules.
    Manufacturers of hard drives record some firmware portions on disk surface not only for purposes of ROM space saving, but also to enable its easy replacement if the manufacturing process or drive operation reveal any errors in a microcode. Internet pages of most manufacturers contain links to utilities used for such updates. Overwriting disk firmware is much easier than unsoldering of hard-programmed microcontrollers. We can remember how Western Digital had to recall a large number of its drives back to factory several years ago…

    Low-level format. Track beginning is identified by an index pulse. Each track is subdivided into data sectors and servo fields. Format of each sector consists of an ID field, data field, synchronization zones and spaces. The beginning of each sector contains a synchronization zone used for phasing and synchronization of data strobe. ID field contains an address marker, physical sector address, flag byte and CRC bytes.
    Format without identifiers has become popular recently. When manufacturers employ such method of data placement along a track ID fields are not used at all (thus increasing available drive capacity). Instead they use a system of servo fields directing to physical sectors on a track. At that reading/writing of all sectors on a track is performed simultaneously (in one disk revolution) to/from RAM containing an image of the read/written track. Thus for reading just one sector a drive copies a whole track to RAM and reading of all subsequent sectors (if necessary) is performed from drive RAM instead of disk surface. Identical operations are performed during recording. During sector recording a drive reads a track, modifies it in RAM and writes the whole track back to disk.

    Configuration tables and settings of hard drives contain information about logical and physical structure of disk space. Those tables enable PCBs, which are identical for the whole drive family, to self-adjust for a certain drive model. As a matter of fact, during design of a certain model like, for example, a 80 Gb drive based on two disks it allows to produce automatically a “half-size” model with 40 Gb capacity based on one disk and “quarter-size” model with 20 Gb capacity based on one side only. Thus a manufacturer can offer a greater number of models with varied capacity for the market without considerable R&D expenses. Besides, junior models can use disks, which for some reasons are unsuitable for full-size models. E.g. “half-size” models can successfully use magnetic disks with defects on one of their surfaces, etc.

    Tables of defects. Modern technology of magnetic disks production does not allow their defect-free manufacture. Heterogeneity of media material, polishing defects, admixtures during magnetic layer application, etc. result in appearance of areas, where data recording or reading end in errors.
    Earlier drives with ST506/412 interface displayed the table of defective tracks as a label on HDA case and any drive had some reserved space, e.g. HDD ST225 (20 Mb) had actual capacity of 21,5 Mb, i.e. 1,5 Mb extra were allocated for defective sectors and tracks. Modern HDDs also have extra capacity, but it is hidden from users and only drive microcontroller can access it. A portion of that extra space is allocated to HDD firmware, configuration tables, S.M.A.R.T. counters, factory information about a HDD, tables of defects, etc. The remaining part is held in reserve for substitution of defective sectors with the reserved ones.
    Tables of defects are filled by the manufacturer during internal factory testing. Numbers of all discovered BAD sectors are added into a table. Such procedure is called updating (relocation) of defects (UPDATE DEFECT). After that if a defective sector is addressed during work with a HDD, the drive itself will redirect the request to a reserved sector. Therefore all modern drives newly arriving from the manufacturing factories have no defective sectors.
    Most HDD models have two tables of defects: Primary or P-List and Grown or G-List. Primary table is filled at the factory during internal testing - SELFSCAN (intelligent burn-in). Grown list is not filled at the factory; it is designed for addition of defects which appear during drive operation. To enable that functionality, the list of user commands practically in all HDDs contains the “assign” command replacing a defective sector with a reserved one. The command is used by numerous test utilities including those recommended by the manufacturers for operations over drives with BAD sectors. Western Digital drives have a Data Lifeguard system, which performs automatic substitution of defective sectors while a drive is idle. In order to perform the procedure, a drive self-tests its surfaces and transfers user data to a reserved sector marking at that defective sector as BAD; the mechanism of defect relocation is identical to the ”assign” command. Manufacturers of Fujitsu, Quantum, Maxtor, and IBM drives implemented a mechanism of automatic defect relocation during the recording process. Thus if data is recorded to a defective sector, a drive itself will redirect such request to the reserved zone marking at that the defective sector as BAD and adding its number to G-List. Among specialized utilities used for relocation of BAD sectors we can note FUJFMT.EXE for Fujitsu drive, WDDIAG.EXE for Western Digital drives, ShDiag.exe offered by Samsung, etc


    يتبع

  3. #3
    عضو
    تاريخ التسجيل
    Jun 2005
    المشاركات
    60
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك


    أسس تغير البردة


    عند تغير بردة هارد هناك عدة عوامل لابد من الاهتمام بها وهي كالتالي مرتبة تبعا لنوع الهاردshould match[/COLOR]



    Hitachi hard disk drives

    for 3.5" models:
    Model
    Firmware
    MLC
    Part Number
    CPU firmware revision should match

    for 2.5" models:
    Model
    Country
    PCB revision match is mandatory
    MLC
    Part Numbe
    r

    ..................


    IBM hard disk drives

    Model
    Firmware
    Country
    Part Number
    For models after AVER there is a strict relation between a head stack type and MLC code, so MLC code must be identical


    .....................


    Maxtor hard disk drives

    Model
    Firmware
    Country
    Third character in alphabetic code type X, X, X, X should match


    ........................


    Quantum hard disk drives

    Model
    Firmware
    For Quantum AS, D540X and D740X, the country and the alphabetic code on the HA must be identica
    l

    .......................


    Samsung hard disk drives

    Manufacturer
    Country
    Forth character in the alphabetic code printed on the label at the rear side of the drive should match


    ......................


    Seagate hard disk drives

    Model
    Firmware
    Country


    ....................


    Toshiba hard drive drives


    Model
    data underneath model (eg. ZE01)
    Country


    ...........................


    Western Digital hard disk

    Model
    Firmware
    In the alphabetic DCM code the sixth (and if you can the fifth, seventh
    and eigth) characters must match


    ..................
    شرح بعض الموديلان


    Western Digital hard disk drives




    اهم شروط تغير البردة في الهارد الويسترن

    1-بلد التصنيع حيث اننا نجد بلاد مختلفه للتصنيع مثل الصين تايلاند سنغافورة

    لذا تطابق البلد يلعب دورا كبيرا في ارتفاع نسبة التوافق (كذلك مع مستخدمي جهاز pc3000 أثناء شحن الفيرم وير)

    2- بيانات التوزيع MATCHING DONOR WESTERN DIGITAL HARD DRIVE PARTS

    كما تبين الصورة التالية



    الموديل:Western Digital MDL: WD2000BB-16DWA0

    MDL: WD2000BB يوضح موديل الهارد والميموري كاش وقد أسهب اخونا sadfriend في رد لاحق في توضيحها

    حيث

    BB = 2MB
    JB = 8MB


    ولابد من تطابق الموديل


    Firmware

    Firmware: 16DWA0
    وهو عامل أساسي في التغير وإن لم تعمل البردة يمكن نقل أيسي السوفت القديم محل الجديد أو شحنها بنفس موديل السوفت وير.

    DCM

    وفي المثال هنا هو DCM: CVJAA

    ولابد من تطابق أخر خمس حروف منه وهو خاص بتوافق الهدود مع سوفت وير

    البردة الجديدة واحيانا يكون هناك تطابق لموديللات مختلفه أو نلجأ لكتابة الفيرم

    وير من جديد بجهاز
    pc3000



    وهناك طريقة أخرى لتغير البردة وهو تطابق الرقم المكتوب على البردة مع البردة

    الجديدة كما توضح الصورة:



    ويكفي ان يتوافق أول10 أراقام منها

    طبعا جهاز pc3000 وفر كل تلك المعانة في تغير البردة

    ...................
    MAXTOR


    بالنسبة للهارد الماكستور فالعملية أكثر بساطة من الويسترن

    حيث يكفي توافق هذا الكود




    أو سنلجأ إلى الخطوات التالية كما توضح الصورة التالية



    لابد من توافق

    1- الكود وأهمية الكود هو توافق رؤوس الكتابة والقراءة

    2-توافق الموديل نمبر ويكفي توافق أول 7 أرقام منه كالتالي 6y160p0

    .....................

    Samsung


    أبسط بكثير مما سبق حيث يكفي فيه توافق الكود فقط كما تبين الصور





    ....................



    Seagate






    لابد من توافق

    1- الموديل

    2- الفيرم وير

    3- بلد التصنيع


    ............................

    DCM


    أثناء شرح توافق البردة ذكرت إختصارا هاما وهو

    DCM

    وكان أول ظهور لهذا المصطلح من شركة IBM

    وكان القصد منه هو توصيف الهندسة الحركية للهدود ومساراتها وتعريفه من خلال

    شركةIBM


    DCM Display Control Module (IBM)

    كذلك له العديد من التعريفات على حسب الشركة المنتجة للهارد ديسك

    Digital Carrier Module

    Data Collection Module


    مثال ذلك من شركة الويسترن ديجتال


    DCM: HSEHYV2AH

    Motor (H)
    Base (S)
    Latch (E)
    Bottom VCM (H)
    Media (Y)
    Headstack (V)
    Actuator-Preamp (2)
    Top VCM (A)
    Separator (H
    )

    وعلى حسب كل جيل من الهاردات يتم اضافة رموز جديدة وتعريف لها


    يتبع

  4. #4
    عضو
    تاريخ التسجيل
    Jun 2005
    المشاركات
    60
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك

    System Area SA.

    هذه المنطقة من الميديا تكون خارج منطقة SPACE area أي خارج المساحة المحددة

    من الهارد لوضع الداتا عليها ونادرا أن تكون داخلها نظرا لأهميتها البالة بالنسبة

    للهارد ديسك.




    يتحرك الهيد لقراءة منطقة النظام والفيرم وير الخاص بهيكلية ميديا الهارد

    تنقسم تلك المنطقة إلى:


    System Area

    Maintenance Tracks

    Negative Cylinders

    Reserved Cylinders

    Calibration Area

    Initialization Area

    Diskware


    وتسمي المعلومات والداتا المكتوبة في تلك المنطقة ب الموديول Module





    وتشمل على

    Smart Data

    وتلف تلك المنطقة تجعل الجهاز يطلب الضغط على مفاتح f1 أو لا يعمل الهارد كماستر مرة اخرى


    System Logs

    شعار النظام

    Serial Number

    الرقم التسلسلي الخاص بالهارد


    Model Numbers

    موديل الهارد


    P-List Primary Defects List

    الجداول الأولية وهذا خاصة بالمصنع ولا ينصه مستخدمي ال

    pc3000 بعمل فورمات لها.


    G-List (Grown Defects Lists – sector relocation table)


    Program Overlays

    وهو البرنامج الخاص بتنفيذ كود الفيرم وير وكذلك عمل تحديث له ان وجد

    Specific Tables like RRO

    تدريج تحريك الهيد وتعديل تلك الحركة


    Zone Tables


    Servo Parameters

    خاصة بحركة الذراع الحامل للرؤوس

    Test Routines

    Factory Defaults Tables

    Recalibration Code Routines

    Translator Data

    وظيفتها

    1- ترجمة العنوان المشفر بالارقام إلى المناطق المقابلة على الهارد

    2- ترجمة حركة الهيد الى السكتور المطلوب على الهارد


    Security Data Passwords for drive

    الباسورد السرية بالهارد ديسك


    وغالبا ما توجد نسختين أو أكثر من System Area على اكثر من اسطوانة من اسطوانات الهارد

    أغلب الوقت معلوماتِ النظامِ تقع على المساراتِ الخارجيةِ - حافة خارجية

    متطرّفة للاسطوانات

    عند تلف البيانات الموجودة في System Area يمكن نسخها مرة اخري من هارد مشابه وهذا يتطلب جهاز خاص





    تتشكل الداتا داخل منطقة النظام على هيئة بلوكات تحتوي تلك البلوكات

    الموديولات الخاصة بالهارد ويطلق عليها
    UBA Modules : Utility Block

    Addressing




    .........................


    عند تصنيع الهارد فانه من المتعارف عليه أنه ستوجد أخطاء في السكتور ولذا تم

    عمل جدولين للبلوكات التالفة تسمى
    bad block tables

    هما:

    P-List

    (Primary Defects List – manufacture defect info that does not change)



    يتم انشائها من قبل المصنع

    G-List

    Grown Defects Lists – sector relocation table

    يتم انشائها عن طريق الاخطاء التي تحدث من الاستخدام اليومي



    أكواد الأخطاء الخاصة بالميديا عن استخدام سوفت وير متقدم أو
    كارت

    pc3000


    والبعض يعتبرها من أسرار هذا الكارت ونادرا ما يبوح بها أحد للأسف
    BSY – drive busy

    DRDY – Drive ready to accept commands

    ERR - The Last Result was an Error

    DREQ -exchange data with host

    UNCR-Uncorrectable Error

    WRFT - Write Fault

    AMNF-Address Marker Not Found

    IDNF- Sector ID Not Found

    ABRT- Command Aborted

    TONF - Track 0 not found


    ..........................


    TRACK ZERO


    نظرة سريعة على التراك صفر نظرا لأهميته


    هو أول مسار في في ميديا الهارد

    1-مع بداية تشغيل الهارد ديسك يتم التالي : يتحرك الهيد مباشرة إلى القطاع زيرو


    SECTOR ONE أو ما يسمى ب

    MBR
    وهو السجل الخاص بعمليلة بدأ التحميل.

    2-بعد قراءة الهيد لل MBR يتحرك إلى السكتور الثاني

    وهو
    PARTIONTABLE

    PARTIONTABLE هو جدول التجزيء الخاص بعدد البرتشنات والسكتور

    على الهارد


    3-بعد ذلك ينتقل الهيد مباشرة الى السكتور 3 وهو SYSTEM FILES

    حيث يحتوي

    على ثلاث ملفات الخاصة بالنظام


    4-بعد ذلك يعود الهيد للخلف ليقرأ منطقة تسمى FAT

    FILE ALLOCATION TABLE جدول تسكين الملفات أو عنواين

    وفهرس الهارد


    ......................

    S.M.A.R.T


    وهي إختصار لـــــــــ

    S.M.A.R.T. i= Self

    Monitoring Analysis and Reporting Technolog


    برنامج تم دمجة في الهاردات الجديدة لعمل مراقبة ذاتية وتحليل التقارير

    الداخلية للهارد أثناء عملية البدء (boot up(


    Troubleshooting a S.M.A.R.T. error

    عند حدوث مشاكل بالسمارت يمكن معالجتها بأحد البرنامجين التاليين طبقا لنصائح موقع الويسترن ديجتال

    Data Lifeguard Diagnostic for DOS

    Data Lifeguard Diagnostic


    إقتباس من موقع الويسترن ديجتال


    Explanation of S.M.A.R.T.:
    S.M.A.R.T. is an acronym Self Monitoring Analysis and Reporting

    Technology. It is used to perform a quick analysis of the hard drive for

    problems during system boot up.

    SMART was originally developed and defined by the SFF committee in the

    mid 90s. SMART had several evolutions that are sometimes referred to as

    SMART I, II and III. Over the years, the T13 committee has taken over

    responsibility for SMART and it is now specified in the ATA

    specification. The ATA Spec does not define SMART I, II, III. WD would

    consider the following to be the definitions:

    SMART I: Defined by SFF-8035i v1.0 Specification (May 1995). SMART is

    calculated from on-line drive activity. On-line means the host system

    requested the drive to perform the activity (such as a read or write.)

    SMART II: Defined by SFF-8035i v2.0 Specification (April 1996). SMART is

    calculated from on-line and off-line drive activity. During idle periods,

    an off-line scan could be performed to scan the entire media of the hard

    drive. These off-line activities affect SMART.

    SMART III: Not defined by any industry standard specification. Off-line

    scan is expanded to include sector repair.

    Troubleshooting a S.M.A.R.T. error:
    If a problem is encountered, you can use Data Lifeguard Diagnostic for

    DOS or a Data Lifeguard Diagnostic for DOS (CD) to perform a more

    detailed analysis of the hard drive. All Western Digital hard drives are

    compatible with S.M.A.R.T. version III.

    Older versions of S.M.A.R.T. in the system BIOS may cause problems while

    scanning the S.M.A.R.T. in your hard drive. If the system BIOS reports a

    S.M.A.R.T. error and our Diagnostics do not report a S.M.A.R.T. error,

    please contact the system or BIOS manufacturer for an updated BIOS

    revision.
    ........................



    ........................

  5. #5
    عضو الصورة الرمزية gim99
    تاريخ التسجيل
    Apr 2008
    المشاركات
    206
    الدولة: Tunisia
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك

    موضوع رااااااااااااااااااااائع يا أخي
    بارك الله فيك و جعله في ميزان حسناتك

    بالتوفيق أخي
    قولوا الحمد لله وصلوا علي رسول الله

    أرجو الدعاء للاخواننا في غزة بالنصر على اليهود الغاصبين إخوة القردة و الخنازير.
    يا شباب هلموا نغير ما بأنفسنا حتى يغير الله حالنا و يعيد لنا العزة بعد الذلة

  6. #6
    عضو برونزي الصورة الرمزية ameer_s
    تاريخ التسجيل
    May 2008
    المشاركات
    1,808
    الدولة: Qatar
    معدل تقييم المستوى
    17

    رد: تشريح الهارد ديسك

    موضوغ متميز

    شكرا لك ,,,,,,,,,

  7. #7
    مخالف للقوانين
    تاريخ التسجيل
    Sep 2007
    المشاركات
    4,715
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك

    موضوع مميز تستحق عليه خمس نجوم

  8. #8
    عضو
    تاريخ التسجيل
    Jun 2005
    المشاركات
    60
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك

    اقتباس المشاركة الأصلية كتبت بواسطة gim99 مشاهدة المشاركة
    موضوع رااااااااااااااااااااائع يا أخي
    بارك الله فيك و جعله في ميزان حسناتك

    بالتوفيق أخي

    الله يبارك فيك ويجزيك أفضل مما قلت وزيادة

  9. #9
    عضو
    تاريخ التسجيل
    Jun 2005
    المشاركات
    60
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك

    اقتباس المشاركة الأصلية كتبت بواسطة ameer_s مشاهدة المشاركة
    موضوغ متميز

    شكرا لك ,,,,,,,,,
    العفو أخي الكريك نورت الموضوع

  10. #10
    عضو
    تاريخ التسجيل
    Jun 2005
    المشاركات
    60
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك

    اقتباس المشاركة الأصلية كتبت بواسطة Tech_Admin مشاهدة المشاركة
    موضوع مميز تستحق عليه خمس نجوم

    جزاك الله خيرا استاذي والخمس نجوم انا حصلت على أكثر منها بتشريفك الموضوع

  11. #11
    عضو محترف الصورة الرمزية شلاع العتر
    تاريخ التسجيل
    Nov 2007
    المشاركات
    11,465
    معدل تقييم المستوى
    98

    رد: تشريح الهارد ديسك

    جزيل الشكر ... طريقتك في الاستعراض جيدة جدا وبالفعل استفدنا كثيرا

  12. #12
    عضو برونزي الصورة الرمزية أيمن النعيمي
    تاريخ التسجيل
    Nov 2007
    المشاركات
    2,600
    معدل تقييم المستوى
    27

    رد: تشريح الهارد ديسك

    مشكور جدا على الشرح القوي التي تفتقر المنتديات العربية اليه
    جعله الله في ميزان اعمالك.
    افهم من الشرح ان اصلاح الهارد ديسك يقتصر فقط على تغيير البردة واصلاحها هو فقط باستبدالها بواحدة جديدة مطابقة لكل ماذكرت.....طريقة استبدال البردة هي بفك البراغي الموجودة وكبل الداتا الموصول بالميديا ام ان هناك شيء آخر يضا؟
    وسؤال اخر ما هي برائيك اكثر اعطال الهارد ديسك ؟
    وهل هناك مايسمى بارجاع الهارد الى حالة المصنع اي كما خرج من المصنع اول مرة ؟؟(لقد قراته في احد المنتديات ولم افهمها فما رائيك؟؟؟
    وهل تغيير مواضع الجامبر في الهاردات الكبيرة الساتا(1 تيرا) يفيد في تسريع نقل البيانات على الهاردديسك؟؟
    اعذرني على كثرة الاسئلة لكن الافادة للجميع

  13. #13
    عضو ذهبي
    تاريخ التسجيل
    Apr 2007
    المشاركات
    1,909
    الدولة: Egypt
    معدل تقييم المستوى
    44

    رد: تشريح الهارد ديسك

    مواضيعك قيمة جدا اخي نور, ما شاء الله عليك..

    جزاك الله خيرا و زادك علما..

    و خمس نجوم
    [CENTER][COLOR=Black][SIZE=3][URL="https://www.arabhardware.net/forum/showthread.php?t=57861"]أسعار و أخبار الهاردوير في السوق المصرية[/URL][/SIZE][/COLOR][URL="https://www.facebook.com/group.php?gid=6972173005"][COLOR=orange][B][SIZE=3][/SIZE][/B][/COLOR][/URL]
    [SIZE=3][URL="https://www.youtube.com/profile?user=stanforduniversity&view=playlists"]Stanford[/URL] [/SIZE][SIZE=3][COLOR=Red][B]|[/B][/COLOR][/SIZE][SIZE=3] [URL="https://www.youtube.com/user/mit?blend=1&ob=4#grid/playlists"]MIT[/URL] [B][COLOR=Red]|[/COLOR][/B] [URL="https://www.youtube.com/ucberkeley#grid/playlists"]Berkely[/URL] [/SIZE][SIZE=3][COLOR=Red][B]|[/B][/COLOR][/SIZE][SIZE=3] [URL="https://www.youtube.com/profile?user=nptelhrd&view=playlists"]NPTEL[/URL][/SIZE] @Youtube

    [COLOR=Black][IMG]https://folding.extremeoverclocking.com/sigs/sigimage.php?un=_Fusion_&t=155660[/IMG][/COLOR]
    [COLOR=DimGray]"اللهم إني أَعُوذُ بِكَ أنْ أضِلَّ أَوْ أُضَلَّ، أوْ أزِلَّ أَوْ أُزَلَّ، أَوْ أظْلِمَ أَوْ أُظْلَمَ، أوْ أجْهَلَ أَوْ يُجْهَلَ عليّ"[/COLOR]
    [/CENTER]

  14. #14
    عضو الصورة الرمزية استشهادى مصرى
    تاريخ التسجيل
    May 2004
    المشاركات
    47
    معدل تقييم المستوى
    0

    رد: تشريح الهارد ديسك

    بارك الله فيك وجزاك الله خيرا
    تشريح ممتاز يدل على حرفية ومهنية عالية المفروض تكون استاذ قسم التشريح فى كلية الطب
    الفرق بين : إن شاء الله و إنشاء الله

  15. #15
    عضو برونزي الصورة الرمزية rezoufda
    تاريخ التسجيل
    Jun 2007
    المشاركات
    3,180
    الدولة: Morocco
    معدل تقييم المستوى
    23

    رد: تشريح الهارد ديسك

    أشكرك أخي على طرح الموضوع بمنتدانا كذلك
    شرح تقني، مهيكل، وشامل ===> ممتاز
    أرجو أن لا تبخل علينا بمواضيعك الاخرى في الصيانة اخي
    وبوركت
    [CENTER][COLOR="#000000"][B]اللهم اغفر للمؤمنين والمؤمنات الأحياء منهم والأموات إنك سميع مجيب الدعوات[/B][/COLOR][/CENTER]
    [B][COLOR="YellowGreen"][CENTER][url]www.rasoulallah.net[/url][/CENTER][/COLOR][/B]

    [CENTER][SIZE="4"]ت.م/ رضا - المغرب
    [/SIZE][/CENTER]
    [CENTER][SIGPIC][/SIGPIC][/CENTER]
    [CENTER]آخر [COLOR="#000000"][/COLOR]مواضيعي:

    [URL="https://www.arabhardware.net/forum/showthread.php?p=1153286#post1153286"][SIZE="2"][B]روتر Wigate الجديد، لمشاركة الـ 3G[/B][/SIZE][/URL]

    [URL="https://www.arabhardware.net/forum/showthread.php?p=960990#post960990"][SIZE="2"][B]كل ما تود معرفته عن معالج intel Atom[/B]
    [/SIZE][/URL]

    [/CENTER]

صفحة 1 من 2 1 2 الأخيرةالأخيرة

المواضيع المتشابهه

  1. مشاركات: 8
    آخر مشاركة: 08-10-2011, 12:50
  2. إلى خبراء الهارد ديسك اريد الحل لاحتراق الهارد
    بواسطة tawfek1990 في المنتدى الأرشيف
    مشاركات: 7
    آخر مشاركة: 26-09-2009, 15:01
  3. إلى خبراء الهارد ديسك اريد الحل لاحتراق الهارد
    بواسطة tawfek1990 في المنتدى مشاكل الحاسب وحلولها
    مشاركات: 4
    آخر مشاركة: 24-09-2009, 02:33
  4. عدم تعرف الجهاز غلى الهارد ديسك بعد ال F ديسك
    بواسطة mitonic في المنتدى الأرشيف
    مشاركات: 4
    آخر مشاركة: 20-07-2009, 12:06
  5. مشكلة في الهارد ديسك لا يظهر اكثر من نصف مساحة الهارد
    بواسطة القطن2005 في المنتدى الأرشيف
    مشاركات: 2
    آخر مشاركة: 03-12-2006, 09:41

الكلمات الدلالية لهذا الموضوع

المفضلات

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •