المشاركة الأصلية كتبت بواسطة Nightspy
قبل ما ارد ااحب اقولك ان الكلام لسة فى بدايتة ونقاش جميل واتمنى ان لا تكون الردود القادمة من كلا الطرفين سواء انا او انت تكون هجوم او تحدى فقط وانما تسود روح المشاكر ما بنا
تعالى نتكلم على الكلام الى انت قولتة
وبعدها راح تآخذ ( اي بي وسبنت ماسك و ديفولت قاتوي ) ...
طيب كيف ياخد الip اذا كان لا يوجد DHCP معد على الinterface ???
ثانيا تعرف ان فى نسخ من سيسكو كثير لا تدعم الGUI اصلا ؟ وان بيلزمها تحديث وهذا كان واضح فى الرابط الذى ارسلته
الشي ء الثالث هل تعلم انك من الممكن ان تدخل على الSDM من اى مكان داخل الLAN ولن تحتاج الى وصلة Cross واتصال Direct بالRouter ?
الشيء الرابع من اعدادات الSDM طويلة وليست by default على ما اتذكر فتخيل لو شخص مبتدىء وذكرت لة هذا الكلام فكيف سوف تكون النتائج ؟!
على العموم هذا شرح لكيفية اضافه الSDM
Step 1 Enable the HTTP and HTTPS servers on your router by entering the following commands in global configuration mode:
Router#
configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#
ip http server
Router(config)#
ip http secure-server
Router(config)#
ip http authentication local
Router(config)#
ip http timeout-policy idle 600 life 86400 requests 10000
If the router supports HTTPS, the HTTPS server will be enabled. If not, the HTTP server will be enabled. HTTPS is supported in all images that support the Crypto/IPSec feature set, starting from Cisco IOS release 12.25(T).
Step 2 Create a user account defined with privilege level 15 (enable privileges). Enter the following command in global configuration mode, replacing
username and
password with the strings that you want to use:
Router(config)#
username username privilege 15 secret 0 password
For example, if you chose the username tomato and the password vegetable, you would enter:
Router(config)#
username tomato privilege 15 secret 0 vegetable
You will use this username and password to log in to SDM.
Step 3 Configure SSH and Telnet for local login and privilege level 15. Use the following commands:
Router(config)#
line vty 0 4
Router(config-line)#
privilege level 15
Router(config-line)#
login local
Router(config-line)#
transport input telnet ssh
Router(config-line)#
exit
If your router supports 16 vty lines, you can add the following lines to the configuration file:
Router(config)#
line vty 5 15
Router(config-line)#
privilege level 15
Router(config-line)#
login local
Router(config-line)#
transport input telnet ssh
Router(config-line)#
exit
Router(config)# وبامكان الاخ صاحب الموضوع الدخول الى هاتين الصفحتين فهن مفيدات جدا
https://www.cisco.com/en/US/products...0803e4727.html
https://www.cisco.com/en/US/products...8073e067.shtml
وجزاكم الله خيرا
المفضلات