النتائج 1 إلى 8 من 8

الموضوع: سؤال عن STP Per-Vlan

  1. #1
    عضوية جديدة
    تاريخ التسجيل
    Apr 2008
    المشاركات
    25
    معدل تقييم المستوى
    0

    سؤال عن STP Per-Vlan

    اخواني الاعزاء
    الاسلام عليكم ورحمة الله بركاته
    عندي عدد من الاسئله عن STP Per-Vlan ارجوا من المساعده
    1- ما الفرق بين Rapid Per-VLAN )rapid-pvst) و pvst فقط ؟؟ وما هي الية عمل كل منهما؟؟
    2- انا عندي عندي شبكاه عامل فيها stp عادي وال command كالاتي :
    spanning-tree extend system-id
    سؤالي انا لو عايز انفذpvstp command لازم امسح ال command اعلاه ولا اعمل ايه؟؟

    3- هل يوجد هناك اي فيديوا يوضح لي الاكلام ده؟؟؟؟؟

  2. #2
    عضو الصورة الرمزية kamel_s_s
    تاريخ التسجيل
    Dec 2008
    المشاركات
    456
    معدل تقييم المستوى
    16

    رد: سؤال عن STP Per-Vlan

    جزاك الله خير اخ warior10 شرح وافي

  3. #3
    عضو ذهبي الصورة الرمزية warior10
    تاريخ التسجيل
    Nov 2005
    المشاركات
    1,989
    الدولة: Saudi Arabia
    معدل تقييم المستوى
    31

    رد: سؤال عن STP Per-Vlan

    الاخ كامل
    متهيالى كلامك على حسب معلوماتي الصغيرة خطأ
    pvst هي pervlan spanning tree
    وهي ليست common spanning tree
    common spt تكون عبارة عن spanning واحدة لكل الشبكة
    اما pvst فتكون stp لكل vlan بمعنى ان لو عندك 10 vlan فى الشبكة سيكون هناك عشرة spanning tree
    Common Spanning Tree
    The IEEE 802.1Q standard specifies how VLANs are to be trunked between switches. It also specifies only a single instance of STP that encompasses all VLANs. This instance is referred to as the Common Spanning Tree (CST). All CST BPDUs are transmitted over trunk links using the native VLAN with untagged frames.Having a single STP for many VLANs simplifies switch configuration and reduces switch CPU

    load during STP calculations. However, having only one STP instance can cause limitations, too. Redundant links between switches will be blocked with no capability for load balancing. Conditions


    also can occur that would cause CST to mistakenly enable forwarding on a link that does not carry a specific VLAN, whereas other links would be blocked



    خلاصة الكلام
    بيقول ان cst هي عمل stp واحدة فقط لكل الشبكة حتى لو بها 1000 vlan
    اما pvst


    Per-VLAN Spanning Tree


    Cisco has a proprietary version of STP that offers more flexibility than the CST version.
    Per-VLAN Spanning Tree (PVST) operates a separate instance of STP for each individual VLAN. This allows the STP on each VLAN to be configured independently, offering better performance and tuning for specific conditions. Multiple spanning-trees also make load balancing possible over redundant

    links when the links are assigned to different VLANs. One link might forward one set of VLANs,while another redundant link might forward a different set.
    Because of its proprietary nature, PVST requires the use of Cisco Inter-Switch Link (ISL) trunking
    encapsulation between switches. In networks where PVST and CST coexist, interoperability problems occur. Each requires a different trunking method, so BPDUs are never exchanged between STP types




    وكما هو واضح فان هناك stp لكل vlan

    والامر يكون بهذا الشكل
    spanning-tree mode pvst

    spanning-tree vlan 1,2,3,4,5,50,38,41,43,60,47,51,80,125,128 priority 8192
    والامر الثاني لعمل root لل vlan المذكورة
    اى لا نعمل السويتش كانه root لكل الشبكة

    مع ملاحظة انه فى الشغل العملى يتم عمل encapsulation ب 802.1 q وليس isl كما هو مذكور
    وهذا مطبق فعلا فى الشبكة التي اعمل عليها
    ومذكور فى الكتب ان هناك pvst+ ولذلك للعمل على 802.1 q
    وذلك للعمل والربط بين CSTو PVST
    واعتقد ان pvst الموجود فى catalyst هو نفسه pvst+

    Per-VLAN Spanning Tree Plus


    Cisco has a second proprietary version of STP that allows devices to interoperate with both PVSTand CST.
    Per-VLAN Spanning Tree Plus (PVST+) effectively supports three groups of STPoperating in the same campus network:


    Catalyst switches running PVST


    +
    Catalyst switches running PVST


    Switches running CST over 802.1Q

    To do this, PVST+ acts as a translator between groups of CST switches and groups of PVSTswitches. PVST+ can communicate directly with PVST by using ISL trunks. To communicate with CST, however, PVST+ exchanges BPDUs with CST as untagged frames over the native
    VLAN. BPDUs from other instances of STP (other VLANs) are propagated across the CST portions of the network by tunneling. PVST+ sends these BPDUs by using a unique multicast address so that the CST switches forward them on to downstream neighbors without interpreting them first. Eventually, the tunneled BPDUs reach other PVST+ switches where they are understood.



    اما RAPID PVST فهي عبارة عن استخدام PVST ولكن نستخدمه معه rapid stp وذلك لتقليل الزمن الذي يأخذه المنفذ للتحول من listen الى learning الى forward
    وهو يكون بمقدار 50 ثانية فى حالة عدم استخدام rapid stp اما عند استخدام rapistp مع اى نوع من انواع stp فأنه يتم تقليل الزمن بمقدار 30 ثانية




    Rapid Per-VLAN Spanning Tree Protocol



    In PVST+, one spanning tree instance is created and used for each active VLANthat is defined on the switch. Each STP instance behaves according to the traditional 802.1D


    STP rules.




    You can improve the efficiency of each STP instance by configuring a switch to begin using RSTP instead. This means that each VLAN will have its own independent instance of RSTP running on the switch. This mode is known as
    Rapid PVST+ (RPVST+).

    You need only one configuration step to change the STP mode and begin using RPVST+. You can use the following global configuration command to accomplish this:




    Switch(config)# spanning-tree mode rapid-pvst


    Be careful when you use this command on a production network because any STP process that is currently running must be restarted. This can cause functioning links to move through the traditional STP states, preventing data from flowing for a short time.




    لمزيد من المعلومات موجود فى كورس bcmsn
    اما الامر الذي استخدمه المهدس
    spanning-tree extend system-id
    فكما علمنا سابقا ان bridg id يتم تعيينه بواسطة جعل اول 2 بايت ل priorty و6 الباقيين ل mac address
    اما باستخدام هذا الامر فاننا نجعل priorty يأخذ فقط 4 بنت من 16 بت الذين انو مخصصين ل priorty
    و 12 الاخرين يكونون ل extended system id ويتم وضعهم يساو رقم vlan

    الخلاصة
    ممكن عمل اى stp بدون حذف هذا الامر
    مع ملاحظة انه عند عمل root فأن هذا الامر سيزيد priorty بمقدار vlan
    بمعنى اننا لو جعلنا priorty ل vlan 100 مثلا يساوي صفر فأننا عند عمل sh spanning tree سنرى priorty تساوي 100 وليست صفر كما وضعنها
    ولو كانت priorty مثلا ل vlan 100 تساو مثلا 4100 فأننا سنراها تساوي 4200

    ده فهمي للموضوع
    والله تعالى اعلى واعلم ولو احد من الاخوة عنده تصحيح يا ريت ما يبخل بيه علينا


    [SIZE=3][COLOR=red]الحــــر يعـــرف مــــــا تــريـــد المحـــــــكمة [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]وقضــــاتها سلفا قـــــد ارتشفوا من دمــــه [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]لا يرتجي دفعا لبهتــــــان رماه به الطغــــاة [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]المجرمون الجالسون فوق كراسي القضاة[/COLOR][/SIZE]

  4. #4
    عضو برونزي
    تاريخ التسجيل
    Feb 2008
    المشاركات
    664
    الدولة: England
    معدل تقييم المستوى
    17

    رد: سؤال عن STP Per-Vlan

    اخي warrior هل ممكن تكبر الخط شويه (اتعميت من اول سطرين):ah46:.

    وعفواً على الازعاج

  5. #5
    عضو ذهبي الصورة الرمزية warior10
    تاريخ التسجيل
    Nov 2005
    المشاركات
    1,989
    الدولة: Saudi Arabia
    معدل تقييم المستوى
    31

    رد: سؤال عن STP Per-Vlan

    تم تكبير الخط يا مهندس تقى الدين
    [SIZE=3][COLOR=red]الحــــر يعـــرف مــــــا تــريـــد المحـــــــكمة [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]وقضــــاتها سلفا قـــــد ارتشفوا من دمــــه [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]لا يرتجي دفعا لبهتــــــان رماه به الطغــــاة [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]المجرمون الجالسون فوق كراسي القضاة[/COLOR][/SIZE]

  6. #6
    عضو برونزي
    تاريخ التسجيل
    Feb 2008
    المشاركات
    664
    الدولة: England
    معدل تقييم المستوى
    17

    رد: سؤال عن STP Per-Vlan

    اقتباس المشاركة الأصلية كتبت بواسطة warior10 مشاهدة المشاركة
    تم تكبير الخط يا مهندس تقى الدين
    اشكرك اخي warior .

  7. #7
    عضو الصورة الرمزية kamel_s_s
    تاريخ التسجيل
    Dec 2008
    المشاركات
    456
    معدل تقييم المستوى
    16

    رد: سؤال عن STP Per-Vlan

    فعلان يا اخ warior10 كلامك انتا اللي مظبوط

  8. #8
    عضو ذهبي الصورة الرمزية warior10
    تاريخ التسجيل
    Nov 2005
    المشاركات
    1,989
    الدولة: Saudi Arabia
    معدل تقييم المستوى
    31

    رد: سؤال عن STP Per-Vlan

    اصل المشكلة ية واجهتني فى الشغل علشان كده قرأت عنها شوية
    [SIZE=3][COLOR=red]الحــــر يعـــرف مــــــا تــريـــد المحـــــــكمة [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]وقضــــاتها سلفا قـــــد ارتشفوا من دمــــه [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]لا يرتجي دفعا لبهتــــــان رماه به الطغــــاة [/COLOR][/SIZE]
    [SIZE=3][COLOR=red]المجرمون الجالسون فوق كراسي القضاة[/COLOR][/SIZE]

المواضيع المتشابهه

  1. شرح سؤال عن vlan
    بواسطة noursh في المنتدى الأرشيف
    مشاركات: 0
    آخر مشاركة: 28-04-2011, 09:16
  2. سؤال فى ال vlan
    بواسطة Dr Virus.exe في المنتدى الأرشيف
    مشاركات: 8
    آخر مشاركة: 20-03-2011, 13:39
  3. سؤال في الـ VLAN !!!
    بواسطة D.I.G في المنتدى الأرشيف
    مشاركات: 18
    آخر مشاركة: 08-01-2010, 20:43
  4. سؤال مهم vlan & inter-vlan
    بواسطة somaaoo في المنتدى الأرشيف
    مشاركات: 4
    آخر مشاركة: 02-01-2010, 07:37
  5. سؤال في VLAN
    بواسطة hiha في المنتدى الأرشيف
    مشاركات: 7
    آخر مشاركة: 28-10-2007, 01:47

الكلمات الدلالية لهذا الموضوع

المفضلات

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •