صفحة 1 من 5 1 2 3 4 5 الأخيرةالأخيرة
النتائج 1 إلى 15 من 74

الموضوع: اوامر Cisco بشكل مفصل

  1. #1
    مشرف الشهادات الدولية
    تاريخ التسجيل
    Jun 2006
    المشاركات
    267
    معدل تقييم المستوى
    0

    اوامر Cisco بشكل مفصل

    السلام عليكم

    وجدت التعليمات بشكل مفصل فأحببت ان اتشارك بها معكم اتمنى ان تكون مفيدة لكم "منقول"

    ROUTER COMMANDS

    TERMINAL CONTROLS:

    Config# terminal editing - allows for enhanced editing commands
    Config# terminal monitor - shows output on telnet session
    Config# terminal ip netmask-format hexadecimal|bit-count|decimal - changes the format of subnet masks

    HOST NAME:
    Config# hostname ROUTER_NAME

    BANNER:

    Config# banner motd # TYPE MESSAGE HERE # - # can be substituted for any character, must start and finish the message

    DESCRIPTIONS:

    Config# description THIS IS THE SOUTH ROUTER - can be entered at the Config-if level

    CLOCK:

    Config# clock timezone Central -6
    # clock set hh:mm:ss dd month yyyy - Example: clock set 14:35:00 25 August 2003

    CHANGING THE REGISTER:

    Config# config-register 0x2100 - ROM Monitor Mode
    Config# config-register 0x2101 - ROM boot
    Config# config-register 0x2102 - Boot from NVRAM

    BOOT SYSTEM:

    Config# boot system tftp FILENAME SERVER_IP - Example: boot system tftp 2600_ios.bin 192.168.14.2
    Config# boot system ROM
    Config# boot system flash - Then - Config# reload

    CDP:

    Config# cdp run - Turns CDP on
    Config# cdp holdtime 180 - Sets the time that a device remains. Default is 180
    Config# cdp timer 30 - Sets the update timer.The default is 60
    Config# int Ethernet 0
    Config-if# cdp enable - Enables cdp on the interface
    Config-if# no cdp enable - Disables CDP on the interface
    Config# no cdp run - Turns CDP off

    HOST TABLE:

    Config# ip host ROUTER_NAME INT_Address - Example: ip host lab-a 192.168.5.1
    -or-
    Config# ip host RTR_NAME INT_ADD1 INT_ADD2 INT_ADD3 - Example: ip host lab-a 192.168.5.1 205.23.4.2 199.2.3.2 - (for e0, s0, s1)

    DOMAIN NAME SERVICES:

    Config# ip domain-lookup - Tell router to lookup domain names
    Config# ip name-server 122.22.2.2 - Location of DNS server
    Config# ip domain-name cisco.com - Domain to append to end of names

    CLEARING COUNTERS:

    # clear interface Ethernet 0 - Clears counters on the specified interface
    # clear counters - Clears all interface counters
    # clear cdp counters - Clears CDP counters

    STATIC ROUTES:

    Config# ip route Net_Add SN_Mask Next_Hop_Add - Example: ip route 192.168.15.0 255.255.255.0 205.5.5.2
    Config# ip route 0.0.0.0 0.0.0.0 Next_Hop_Add - Default route
    -or-
    Config# ip default-network Net_Add - Gateway LAN network

    IP ROUTING:

    Config# ip routing - Enabled by default
    Config# router rip
    -or-
    Config# router igrp 100
    Config# interface Ethernet 0
    Config-if# ip address 122.2.3.2 255.255.255.0
    Config-if# no shutdown

    IPX ROUTING:
    Config# ipx routing
    Config# interface Ethernet 0
    Config# ipx maximum-paths 2 - Maximum equal metric paths used
    Config-if# ipx network 222 encapsulation sap - Also Novell-Ether, SNAP, ARPA on Ethernet. Encapsulation HDLC on serial
    Config-if# no shutdown

    ACCESS LISTS:
    IP Standard 1-99
    IP Extended 100-199
    IPX Standard 800-899
    IPX Extended 900-999
    IPX SAP Filters 1000-1099

    IP STANDARD:

    Config# access-list 10 permit 133.2.2.0 0.0.0.255 - allow all src ip’s on network 133.2.2.0
    -or-

    Config# access-list 10 permit host 133.2.2.2 - specifies a specific host
    -or-

    Config# access-list 10 permit any - allows any address
    Config# int Ethernet 0
    Config-if# ip access-group 10 in - also available: out

    IP EXTENDED:

    Config# access-list 101 permit tcp 133.12.0.0 0.0.255.255 122.3.2.0 0.0.0.255 eq telnet
    -protocols: tcp, udp, icmp, ip (no sockets then), among others
    -source then destination address
    -eq, gt, lt for comparison
    -sockets can be numeric or name (23 or telnet, 21 or ftp, etc)
    -or-
    Config# access-list 101 deny tcp any host 133.2.23.3 eq www
    -or-
    Config# access-list 101 permit ip any any
    Config# interface Ethernet 0
    Config-if# ip access-group 101 out

    IPX STANDARD:

    Config# access-list 801 permit 233 AA3 - source network/host then destination network/host
    -or-

    Config# access-list 801 permit -1 -1 - “-1” is the same as “any” with network/host addresses
    Config# interface Ethernet 0
    Config-if# ipx access-group 801 out

    IPX EXTENDED:

    Config# access-list 901 permit sap 4AA all 4BB all
    - Permit protocol src_add socket dest_add socket
    -“all” includes all sockets, or can use socket numbers
    -or-

    Config# access-list 901 permit any any all any all
    -Permits any protocol with any address on any socket to go anywhere
    Config# interface Ethernet 0
    Config-if# ipx access-group 901 in

    IPX SAP FILTER:
    Config# access-list 1000 permit 4aa 3 - “3” is the service type
    -or-
    Config# access-list 1000 permit 4aa 0 - service type of “0” matches all services
    Config# interface Ethernet 0
    Config-if# ipx input-sap-filter 1000 - filter applied to incoming packets
    -or-
    Config-if# ipx output-sap-filter 1000 - filter applied to outgoing packets

    NAMED ACCESS LISTS:
    Config# ip access-list standard LISTNAME
    -can be ip or ipx, standard or extended
    -followed by the permit or deny list
    Config# permit any
    Config-if# ip access-group LISTNAME in
    -use the list name instead of a list number
    -allows for a larger amount of access-lists

    PPP SETUP:
    Config-if# encapsulation ppp
    Config-if# ppp authentication chap pap
    -order in which they will be used
    -only attempted with the authentification listed
    -if one fails, then connection is terminated
    Config-if# exit
    Config# username Lab-b password 123456
    -username is the router that will be connecting to this one
    -only specified routers can connect
    -or-
    Config-if# ppp chap hostname ROUTER
    Config-if# ppp chap password 123456
    -if this is set on all routers, then any of them can connect to any other
    -set same on all for easy configuration

    ISDN SETUP:
    Config# isdn switch-type basic-5ess - determined by telecom
    Config# interface serial 0
    Config-if# isdn spid1 2705554564 - isdn “phonenumber” of line 1
    Config-if# isdn spid2 2705554565 - isdn “phonenumber” of line 2
    Config-if# encapsulation PPP - or HDLC, LAPD

    DDR - 4 Steps to setting up ISDN with DDR
    1. Configure switch type
    Config# isdn switch-type basic-5ess - can be done at interface config
    2. Configure static routes
    Config# ip route 123.4.35.0 255.255.255.0 192.3.5.5 - sends traffic destined for 123.4.35.0 to 192.3.5.5
    Config# ip route 192.3.5.5 255.255.255.255 bri0 - specifies how to get to network 192.3.5.5 (through bri0)
    3. Configure Interface
    Config-if# ip address 192.3.5.5 255.255.255.0
    Config-if# no shutdown
    Config-if# encapsulation ppp
    Config-if# dialer-group 1 - applies dialer-list to this interface
    Config-if# dialer map ip 192.3.5.6 name Lab-b 5551212
    connect to lab-b at 5551212 with ip 192.3.5.6 if there is interesting traffic
    can also use “dialer string 5551212” instead if there is only one router to connect to
    4. Specify interesting traffic
    Config# dialer-list 1 ip permit any
    -or-
    Config# dialer-list 1 ip list 101 - use the access-list 101 as the dialer list
    5. Other Options
    Config-if# hold-queue 75 - queue 75 packets before dialing
    Config-if# dialer load-threshold 125 either
    -load needed before second line is brought up
    -“125” is any number 1-255, where % load is x/255 (ie 125/255 is about 50%)
    -can check by in, out, or either
    Config-if# dialer idle-timeout 180
    -determines how long to stay idle before terminating the session
    -default is 120
    FRAME RELAY SETUP:
    Config# interface serial 0
    Config-if# encapsulation frame-relay - cisco by default, can change to ietf
    Config-if# frame-relay lmi-type cisco - cisco by default, also ansi, q933a
    Config-if# bandwidth 56
    Config-if# interface serial 0.100 point-to-point - subinterface
    Config-if# ip address 122.1.1.1 255.255.255.0
    Config-if# frame-relay interface-dlci 100
    -maps the dlci to the interface
    -can add BROADCAST and/or IETF at the end
    Config-if# interface serial 1.100 multipoint
    Config-if# no inverse-arp - turns IARP off; good to do
    Config-if# frame-relay map ip 122.1.1.2 48 ietf broadcast
    -maps an IP to a dlci (48 in this case)
    -required if IARP is turned off
    -ietf and broadcast are optional
    Config-if# frame-relay map ip 122.1.1.3 54 broadcast
    SHOW COMMANDS

    Show access-lists - all access lists on the router
    Show cdp - cdp timer and holdtime frequency
    Show cdp entry * - same as next
    Show cdp neighbors detail - details of neighbor with ip add and ios version
    Show cdp neighbors - id, local interface, holdtime, capability, platform portid
    Show cdp interface - int’s running cdp and their encapsulation
    Show cdp traffic - cdp packets sent and received
    Show controllers serial 0 - DTE or DCE status
    Show dialer - number of times dialer string has been reached, other stats
    Show flash - files in flash
    Show frame-relay lmi - lmi stats
    Show frame-relay map - static and dynamic maps for PVC’s
    Show frame-relay pvc - pvc’s and dlci’s
    Show history - commands entered
    Show hosts - contents of host table
    Show int f0/26 - stats of f0/26
    Show interface Ethernet 0 - show stats of Ethernet 0
    Show ip - ip config of switch
    Show ip access-lists - ip access-lists on switch
    Show ip interface - ip config of interface
    Show ip protocols - routing protocols and timers
    Show ip route - Displays IP routing table
    Show ipx access-lists - same, only ipx
    Show ipx interfaces - RIP and SAP info being sent and received, IPX addresses
    Show ipx route - ipx routes in the table
    Show ipx servers - SAP table • Show ipx traffic - RIP and SAP info
    Show isdn active - number with active status
    Show isdn status - shows if SPIDs are valid, if connected
    Show mac-address-table - contents of the dynamic table
    Show protocols - routed protocols and net_addresses of interfaces
    Show running-config - dram config file
    Show sessions - connections via telnet to remote device
    Show startup-config - nvram config file
    Show terminal - shows history size
    Show trunk a/b - trunk stat of port 26/27
    Show version - ios info, uptime, address of switch
    Show vlan - all configured vlan’s
    Show vlan-membership - vlan assignments
    Show vtp - vtp configs
    CATALYST COMMANDS
    For Native IOS - Not CatOS

    SWITCH ADDRESS:
    Config# ip address 192.168.10.2 255.255.255.0
    Config# ip default-gateway 192.168.10.1

    DUPLEX MODE:
    Config# interface Ethernet 0/5 - “fastethernet” for 100 Mbps ports
    Config-if# duplex full - also, half | auto | full-flow-control

    SWITCHING MODE:
    Config# switching-mode store-and-forward - also, fragment-free

    MAC ADDRESS CONFIGS:
    Config# mac-address-table permanent aaab.000f.ffef e0/2 - only this mac will work on this port
    Config# mac-address-table restricted static aaab.000f.ffef e0/2 e0/3
    -port 3 can only send data out port 2 with that mac
    -very restrictive security
    Config-if# port secure max-mac-count 5 - allows only 5 mac addresses mapped to this port

    VLANS:
    Config# vlan 10 name FINANCE
    Config# interface Ethernet 0/3
    Config-if# vlan-membership static 10

    TRUNK LINKS:
    Config-if# trunk on - also, off | auto | desirable | nonegotiate
    Config-if# no trunk-vlan 2
    -removes vlan 2 from the trunk port
    -by default, all vlans are set on a trunk port

    CONFIGURING VTP:
    Config# delete vtp - should be done prior to adding to a network
    Config# vtp server - the default is server, also client and transparent
    Config# vtp domain Camp - name doesn’t matter, just so all switches use the same
    Config# vtp password 1234 - limited security
    Config# vtp pruning enable - limits vtp broadcasts to only switches affected
    Config# vtp pruning disable

    FLASH UPGRADE:
    Config# copy tftp://192.5.5.5/configname.ios opcode - “opcode” for ios upgrade, “nvram” for startup config

    DELETE STARTUP CONFIG:
    Config# delete nvram
    شارك و لو بابتسامة!Clap !Clap

    يخاطبني السفيه بكل قبح ***** فأكره ان اكون له مجيبا
    يزيد سفاهة فأزيد حلما ******* كعود زاده الإحراق طيبا

    تعرف على تعليمات Cisco بالتفصيل

  2. #2
    عضو
    تاريخ التسجيل
    Jun 2006
    المشاركات
    65
    الدولة: Egypt
    معدل تقييم المستوى
    0

    مشاركة: اوامر Cisco بشكل مفصل

    جزاك الله خيرا يا اخى dekor50 وجعله الله فى ميزان حسناتك يوم القيامة

  3. #3
    عضو الصورة الرمزية myhome
    تاريخ التسجيل
    Jun 2006
    المشاركات
    212
    معدل تقييم المستوى
    0

    مشاركة: اوامر Cisco بشكل مفصل

    بسم الله الرحمن الرحيم
    و الله موضوع جميل منك
    جزاك الله خيرا
    فى حفظ الله

  4. #4
    عضو الصورة الرمزية gezery
    تاريخ التسجيل
    Dec 2006
    المشاركات
    110
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    ما شاء الله أخي الكريم جزاك الله كل خير
    CCNA Certified


    أتهــــزأ بالدُعــــاء وتزدريْــــــــــــهِ ** ومـا تــدري بمـــا صنــع الدعـــاء ُ
    سهـــامُ الليــل لا تُخطـي ولكــنْ ** لهـــا أمــــدُ وللأمــــد انقضــــــاءُ

  5. #5
    عضو الصورة الرمزية BigDaddy
    تاريخ التسجيل
    Feb 2007
    المشاركات
    334
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    عظيم عظيم

    شكرا لك


    (BB) (BB)

  6. #6
    مشرف الشهادات الدولية
    تاريخ التسجيل
    Jun 2006
    المشاركات
    267
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    شكرا الكم على الردود
    شارك و لو بابتسامة!Clap !Clap

    يخاطبني السفيه بكل قبح ***** فأكره ان اكون له مجيبا
    يزيد سفاهة فأزيد حلما ******* كعود زاده الإحراق طيبا

    تعرف على تعليمات Cisco بالتفصيل

  7. #7
    بانتظار تفعيل البريد الإلكتروني
    تاريخ التسجيل
    Mar 2006
    المشاركات
    200
    الدولة: Turkey
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    جزاك الله خيرا على النقل الرائع

  8. #8
    عضو الصورة الرمزية وليد
    تاريخ التسجيل
    Dec 2003
    المشاركات
    548
    الدولة: Saudi Arabia
    معدل تقييم المستوى
    21

    رد: اوامر Cisco بشكل مفصل

    thank you sir
    TaKe a Massive Step

  9. #9
    عضو
    تاريخ التسجيل
    May 2004
    المشاركات
    447
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    مشكور عموه ...ولك علي إني امر عليها واحد واحد

    أخوكم شاكرا
    ابن الولاية
    لتكن رسالتك للعالم كله هي ... الحب

  10. #10
    عضو
    تاريخ التسجيل
    Apr 2007
    المشاركات
    94
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    جزاك الله خيرا
    فعلا ملخص رائع

  11. #11
    عضو
    تاريخ التسجيل
    Jun 2006
    المشاركات
    835
    الدولة: France
    معدل تقييم المستوى
    21

    رد: اوامر Cisco بشكل مفصل

    جزااااااااك الله خيرا

    عمل متقن وجيد بالتوفيق
    تحياتي

  12. #12
    عضو
    تاريخ التسجيل
    Mar 2007
    المشاركات
    484
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    السلام عليكم
    موضوع ممتاز أخى بارك الله فيك
    لكن ماذكرت اى اصدار هذه الاوامر وهل تختلف بين الاصدارات؟
    _____________
    Yasser Kassem

  13. #13
    عضو الصورة الرمزية baamrani
    تاريخ التسجيل
    May 2007
    المشاركات
    84
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    جزاك الله خيرا جزاك الله خيرا جزاك الله خيرا جزاك الله خيرا

  14. #14
    عضو
    تاريخ التسجيل
    Apr 2006
    المشاركات
    206
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    السلام عليكم ورحمة الله وبركاته

    شكرا جزيلا بارك الله فيك

  15. #15
    عضو الصورة الرمزية الحنـــــون
    تاريخ التسجيل
    Sep 2005
    المشاركات
    50
    معدل تقييم المستوى
    0

    رد: اوامر Cisco بشكل مفصل

    مشكور أخي الكريم على المجهود لطيب
    وجعله الله في ميزان حسناتك

صفحة 1 من 5 1 2 3 4 5 الأخيرةالأخيرة

المواضيع المتشابهه

  1. طلب اوامر برجمة switch cisco والانظمة التي نستطيع برمجتها عليه
    بواسطة ذكرى انسان في المنتدى الأرشيف
    مشاركات: 2
    آخر مشاركة: 30-08-2012, 12:43
  2. مشاركات: 0
    آخر مشاركة: 27-07-2011, 03:31
  3. سيسكو تفتح مشروعها التعليمي Cisco Live Virtual بشكل مجاني
    بواسطة m3tasm_elzayat في المنتدى الأرشيف
    مشاركات: 0
    آخر مشاركة: 26-06-2011, 23:55
  4. اوامر مفيدة Good cisco IOS command
    بواسطة kamel_s_s في المنتدى الأرشيف
    مشاركات: 8
    آخر مشاركة: 11-10-2009, 09:20
  5. مشاركات: 1
    آخر مشاركة: 05-09-2003, 12:56

الكلمات الدلالية لهذا الموضوع

المفضلات

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •