النتائج 1 إلى 3 من 3

الموضوع: ممكن مساعدة في حل اسئلة DELL dcse server v10 certification

  1. #1
    عضوية جديدة
    تاريخ التسجيل
    May 2009
    المشاركات
    4
    معدل تقييم المستوى
    0

    ممكن مساعدة في حل اسئلة DELL dcse server v10 certification

    ممكن مساعدة في حل اسئلة محتاج ضروري مساعدة


    (1)Which two components must be removed before removing the processor shroud on the PowerEdge T605?'

    system fan
    memory
    system cover
    expansion card shroud


    (2)TPM is implemented in Dell servers as:
    Hardware
    Wetware
    Software
    Firmware


    (3)Choose All That Apply
    Which of the following are possible causes of the PowerEdge T105 server not retaining the configuration settings at system boot?

    The system power button has been engaged
    The system was not shutdown correctly
    NVRAM_CL jumper is currently enabled
    Defective coin-cell CMOS battery


    (4)After servicing a PowerEdge T300 system, you notice that the LCD is blinking blue. What should you do to address this system's behavior?

    Reseat all components you replaced
    Tell the customer the system is working properly
    Take the system out of the system ID state and ensure there are no error messages on the system LCD.


    (5)The PowerEdge R905 server contains an internal SD Card socket on the system board for use with Vmware ESX embedded virtualization software.

    True
    False



    (6)Multiple Choice
    Steve is unable to boot from the CD-ROM drive on his PowerEdge R805. He needs to reseat the cable. Where does the CD-ROM plug into?

    The CD-ROM plugs into the daughter card.
    The CD-ROM plugs directly into the SATA controller on the planar.
    The CD-ROM plugs directly into the IDE controller on the planar.
    The CD-ROM plugs into an optional PCIe card.

    (7)
    Choose All That Apply
    Which of the following are availability features of PowerEdge R300?

    Support for PCI-e
    Optional Hot Plug physical disk drives
    TPM module
    Optional redundant power supplies


    (Choose All That Apply
    A PowerEdge R200 displays a yellow-yellow-green-yellow diagnostic LED code, where can you go to to find more information to troubleshoot this issue.

    Tell the customer that error message is normal.
    Support.dell.com
    dcse.dell.com

    (9)Multiple Choice
    How does the depth dimension (in terms of how far does it go into a 24U or 42U rack) of the CR100 Compare to the PE R200?

    it is the same as the PowerEdge R200
    increased
    reduced

    (10)Multiple Choice
    Which of the following is true about migrating virtual disks between PERC6 controllers and PERC5 controllers?

    All virtual disks created on a PERC6 can be migrated to a PERC5.
    All virtual disks created on either set of controllers can be migrating to the other set of controllers.
    All virtual disks created on a PERC5 can be migrated to a PERC6.

    (11)
    Multiple Choice
    To remove and replace the DRAC (Dell Remote Access Controller) on the PowerEdge R900, which component must be removed form the system first?
    The Expansion Riser
    Memory Risers
    The processors

    (12)You have just replaced all the memory in a PET605 with 8, 1 GB dimms. When you boot the system, the os only shows 4 gig’s of memory. What could be the cause?

    The system only supports 4 Gigabytes of memory
    Memory raid is enabled
    Memory sparing is enabled


    (13)
    Multiple Choice
    On the PowerEdge R905, how many interface cables must be removed from a PERC 6 before removing the card?
    1
    2
    0

    (14)Rick is wanting to set up memory sparing. It doesn't give him the option in the system bios. The option isn't available. What should he check? The R805 doesn't support memory sparing.
    The system doesn't have all of the memory slots populated.
    Rick needs to set the sparing jumper on the system board.
    The system has too many memory slots populated.

    (15)

    Multiple Choice
    A customer says that when he turns on his system he gets the following error on POST, “Alert! Redundant memory disabled! Memory configuration does not support redundant memory.” Which one of the options below is a possible cause of this error message?
    A spare rank event occurred during the previous boot.
    Faulty or improperly installed memory modules.
    The memory configuration does not support node interleaving. The system will run but with reduced functionality.
    Redundant memory was set to enable in CMOS, but the current configuration does not support redundant memory.

    (16)
    Multiple Choice, Complete the sentence
    When both optional redundant power supplies are installed in a PowerEdge T300 system, ______.
    only the right power supply delivers power, while the left power supply serves as a 'hot standby'.
    both power supplies operate in a standby mode, while main power is provided by the nonredundant power supply.
    the system distributes the power load across both power supplies to maximize efficiency.
    only the left power supply delivers power, while the right power supply serves as a 'hot standby'.




    (17)Choose All That Apply

    A customer contacts Enterprise support stating that his system reports a E1A1C LCD status message on his PowerEdge R905 system. What online resources can you use to find what the error message means?

    Support.dell.com
    Tell the customer that error message is normal



    Dcse.dell.com

    (1
    Multiple Choice
    After replacing the system board on R805, the system reports a boot failure. The customer informs you that they boot from the SD card. What should you check?
    Tell customer his os is corrupt and he needs to reinstall
    Flash the BIOS
    Make sure the boot order is set accordingly


    (19)
    Choose All That Apply
    A PowerEdge R200 displays a yellow-yellow-green-yellow diagnostic LED code, where can you go to to find more information to troubleshoot this issue.
    Tell the customer that error message is normal.
    dcse.dell.com
    Support.dell.com


    (20)
    Multiple Choice
    How does the depth dimension (in terms of how far does it go into a 24U or 42U rack) of the CR100 Compare to the PE R200?
    reduced
    it is the same as the PowerEdge R200
    increased


    (21)
    Multiple Choice
    What is the minimum number of drives needed to create a RAID 6?
    2
    6
    8
    4


    (22)
    Multiple Choice
    You are onsite to replace optical drive on Jamie’s PowerEdge R900 system. He states that the system was working fine until this morning and now it is reporting error E2011 on the LCD Status screen on the front of the system. Select all of the options below where you could go to find information that could help you solve the problem.
    support.dell.com
    Tell the customer that the system is running normally.
    dcse.dell.com


    (23)
    Choose All That Apply
    Which of the following are required actions when removing a optical drive from the PowerEdge T105?
    Push the sliding plate lever towards the base of the computer.
    Remove the computer cover.
    Rotate the hard-drive carrier to the service position.
    Remove the front bezel assembly.


    (24)
    True or False
    The PowerEdge R905 server contains an internal SD Card socket on the system board for use with Vmware ESX embedded virtualization software.
    True
    False


    (25)
    Multiple Choice
    You are asked to replace a PEM (Porcessor Expansion Module) Riser on a PowerEdge R905, which steps below must be performed before replacing the PEM Riser?
    Remove the four front system fans
    Remove all of the expansion cards
    Turn off the system, including any peripherals and disconnect the system from the electrical outlet.
    Remove the Processor Expansion Module
    Remove the system cover


    (26)
    Choose All That Apply
    You are attempting to boot to a CD in the optical drive on a PowerEdge R200, however the system boots straight to the hard disk drive. Which options below would assist you in troubleshooting this issue?
    Ensure the optical drive is seen in the BIOS
    Presss F12 at the Dell P.O,S.T. screen to set the boot option
    Check the book sequece in the BIOS to ensure that the optical drive is set first.

    (27)
    Multiple Choice
    Which diagnostic indicator on the PowerEdge T605 will help troubleshoot issues during POST?
    BIOS status messages
    LCD status messages
    Quad pack diagnostic LEDs on the back of the system


    (2
    Multiple Choice
    On the PowerEdge T605, which keystroke should the user press during POST to access the BMC/DRAC 5 BIOS?
    F2
    CTRL-S
    CTRL-R
    CTRL-E


    (29)
    Multiple Choice
    A customer says that when he turns on his system he gets the following error on POST, “Alert! Redundant memory disabled! Memory configuration does not support redundant memory.” Which one of the options below is a possible cause of this error message?
    The memory configuration does not support node interleaving. The system will run but with reduced functionality.
    A spare rank event occurred during the previous boot.
    Redundant memory was set to enable in CMOS, but the current configuration does not support redundant memory.
    Faulty or improperly installed memory modules.


    (30)
    Multiple Choice
    If you are using the Trusted Platform Module (TPM) with an encryption application such as BitLocker drive encryption, when replacing the system board you must supply ________ when you restart your system or application before you can access the encrypted data on your hard drive(s).
    the trusted USB key
    the Dell Master TPM recovery password
    a local Administrator password
    the TPM recovery key


    (31)
    The Trusted Platform Module (TPM) is designed to:
    Authenticate trusted users
    Encrypt usernames and system logins
    Secure end to end network communication
    Serve as a cryptographic foundation to a trusted environment




    (32)
    Multiple Choice
    After replacing the system board on R805, the system reports a boot failure. The customer informs you that they boot from the SD card. What should you check?
    Make sure the boot order is set accordingly
    Flash the BIOS
    Tell customer his os is corrupt and he needs to reinstall


    (33)
    Multiple Choice
    Steve is unable to boot from the CD-ROM drive on his PowerEdge R805. He needs to reseat the cable. Where does the CD-ROM plug into?
    The CD-ROM plugs directly into the IDE controller on the planar.
    The CD-ROM plugs into the daughter card.
    The CD-ROM plugs directly into the SATA controller on the planar.
    The CD-ROM plugs into an optional PCIe card.


    (34)
    Multiple Choice
    Stephanie wants to install an optional DRAC5 card on her PowerEdge R805. She wants to know what slot to install the card in. Where should it be installed?
    RAC_CONN1 and RAC_CONN2 connectors on the system board.
    Slot 1
    Slot 2
    Slot 3


    (35)
    Multiple Choice
    To remove and replace the DRAC (Dell Remote Access Controller) on the PowerEdge R900, which component must be removed form the system first?
    The processors
    Memory Risers
    The Expansion Riser


    (36)
    Multiple Choice
    You are onsite to replace some parts for Richard’s PowerEdge R900 server. The system is currently in a no P.O.S.T. state. You need to remove some components to get the server down to its base configuration. The server was purchased with 4 processors, and to get the server to its base configuation, also known as its minimum to P.O.S.T. configuration you need to remove all but one processor. Which Processor should you keep?
    The processor in socket 3
    The processor in socket 1
    The processor in socket 2
    The processor in socket 4


    (36)
    Multiple Choice
    You are onsite to replace optical drive on Jamie’s PowerEdge R900 system. He states that the system was working fine until this morning and now it is reporting error E2011 on the LCD Status screen on the front of the system. Select all of the options below where you could go to find information that could help you solve the problem.
    Tell the customer that the system is running normally.
    support.dell.com
    dcse.dell.com


    (37)
    Multiple Choice
    Which PowerEdge R905 BIOS setting must be disabled to allow Non-Uniform Memory Access?
    Uniform Memory Access
    Memory Arch Function
    NUMA
    Node Interleaving


    (3
    Multiple Choice
    What keys must be pressed during post on the PowerEdge R905 server module as the SAS 6 i/R is recognized, to enter the configuration utility?
    Ctrl and C
    Ctrl and X
    Ctrl and M
    Ctrl and A


    (39)
    Multiple Choice
    The asset tag utility should be used to set the service tag on a PowerEdge T605 when:
    Replacing the system board
    Replacing both hard-disk drives
    Replacing the processors
    A BIOS flash fails


    (40)
    Multiple Choice
    What RAID levels are supported by PERC6 controllers?
    0, 1, 6, and 60
    0, 1, 5, 10 and 50
    0, 1, 5, 6, 10, 50, and 60
    0, 1, 5, and 10


    (41)
    Multiple Choice
    What is the minimum number of drives needed to create a RAID 6?
    8
    6
    2
    4


    (42)Multiple Choice
    Which of the following is true about migrating virtual disks between PERC6 controllers and PERC5 controllers?
    All virtual disks created on either set of controllers can be migrating to the other set of controllers.
    All virtual disks created on a PERC5 can be migrated to a PERC6.
    All virtual disks created on a PERC6 can be migrated to a PERC5.
    (43)
    Multiple Choice
    How many drives can a RAID 6 lose before failing?
    3
    4
    1
    2

  2. #2
    عضوية جديدة
    تاريخ التسجيل
    May 2009
    المشاركات
    4
    معدل تقييم المستوى
    0

    رد: ممكن مساعدة في حل اسئلة DELL dcse server v10 certification

    رفع محتاج مساعدة

  3. #3
    عضوية جديدة
    تاريخ التسجيل
    Jun 2008
    المشاركات
    74
    الدولة: Tunisia
    معدل تقييم المستوى
    0

    رد: ممكن مساعدة في حل اسئلة DELL dcse server v10 certification

    SALAMO ALIKOM
    I'am a HP technical Support Engineer
    I try to help you in this quizz
    So i have answer t the questions but not all
    you must verify if his content a mistake because i know the HP Server Technologie but for DEll not yet
    ============================================
    (1)Which two components must be removed before removing the processor shroud on the PowerEdge T605?'

    system fan
    memory
    system cover ***
    expansion card shroud


    (2)TPM is implemented in Dell servers as:
    Hardware
    Wetware
    ***Software
    Firmware


    (3)Choose All That Apply
    Which of the following are possible causes of the PowerEdge T105 server not retaining the configuration settings at system boot?

    The system power button has been engaged
    The system was not shutdown correctly ***
    NVRAM_CL jumper is currently enabled ***
    Defective coin-cell CMOS battery ***


    (4)After servicing a PowerEdge T300 system, you notice that the LCD is blinking blue. What should you do to address this system's behavior?

    Reseat all components you replaced
    Tell the customer the system is working properly
    Take the system out of the system ID state and ensure there ****are no error messages on the system LCD.


    (5)The PowerEdge R905 server contains an internal SD Card socket on the system board for use with Vmware ESX embedded virtualization software.

    True ***
    False



    (6)Multiple Choice
    Steve is unable to boot from the CD-ROM drive on his PowerEdge R805. He needs to reseat the cable. Where does the CD-ROM plug into?

    The CD-ROM plugs into the daughter card.
    The CD-ROM plugs directly into the SATA controller on the planar. ****
    The CD-ROM plugs directly into the IDE controller on the planar.
    The CD-ROM plugs into an optional PCIe card.

    (7)
    Choose All That Apply
    Which of the following are availability features of PowerEdge R300?

    Support for PCI-e ***
    Optional Hot Plug physical disk drives
    TPM module
    ***Optional redundant power supplies


    (Choose All That Apply
    A PowerEdge R200 displays a yellow-yellow-green-yellow diagnostic LED code, where can you go to to find more information to troubleshoot this issue.

    Tell the customer that error message is normal.
    Support.dell.com
    dcse.dell.com

    (9)Multiple Choice
    How does the depth dimension (in terms of how far does it go into a 24U or 42U rack) of the CR100 Compare to the PE R200?

    it is the same as the PowerEdge R200
    increased
    reduced

    (10)Multiple Choice
    Which of the following is true about migrating virtual disks between PERC6 controllers and PERC5 controllers?

    All virtual disks created on a PERC6 can be migrated to a PERC5.
    All virtual disks created on either set of controllers can be migrating to the other set of controllers.
    All virtual disks created on a PERC5 can be migrated to a PERC6.

    (11)
    Multiple Choice
    To remove and replace the DRAC (Dell Remote Access Controller) on the PowerEdge R900, which component must be removed form the system first?
    The Expansion Riser ***
    Memory Risers
    The processors

    (12)You have just replaced all the memory in a PET605 with 8, 1 GB dimms. When you boot the system, the os only shows 4 gig’s of memory. What could be the cause?

    The system only supports 4 Gigabytes of memory ***
    Memory raid is enabled
    Memory sparing is enabled


    (13)
    Multiple Choice
    On the PowerEdge R905, how many interface cables must be removed from a PERC 6 before removing the card?
    1 ***
    2 ***
    0

    (14)Rick is wanting to set up memory sparing. It doesn't give him the option in the system bios. The option isn't available. What should he check? The R805 doesn't support memory ****sparing.
    The system doesn't have all of the memory slots populated.
    Rick needs to set the sparing jumper on the system board. ****
    The system has too many memory slots populated.

    (15)

    Multiple Choice
    A customer says that when he turns on his system he gets the following error on POST, “Alert! Redundant memory disabled! Memory configuration does not support redundant memory.” Which one of the options below is a possible cause of this error message?
    A spare rank event occurred during the previous boot. ***
    Faulty or improperly installed memory modules.
    The memory configuration does not support node interleaving. The system will run but with reduced functionality.
    ***Redundant memory was set to enable in CMOS, but the current configuration does not support redundant memory.

    (16)
    Multiple Choice, Complete the sentence
    When both optional redundant power supplies are installed in a PowerEdge T300 system, ______.
    only the right power supply delivers power, while the left power supply serves as a 'hot standby'.
    both power supplies operate in a standby mode, while main power is provided by the nonredundant power supply.
    the system distributes the power load across both power supplies to maximize efficiency.
    only the left power supply delivers power, while the right power supply serves as a 'hot standby'.




    (17)Choose All That Apply

    A customer contacts Enterprise support stating that his system reports a E1A1C LCD status message on his PowerEdge R905 system. What online resources can you use to find what the error message means?

    Support.dell.com
    Tell the customer that error message is normal



    Dcse.dell.com

    (1
    Multiple Choice
    After replacing the system board on R805, the system reports a boot failure. The customer informs you that they boot from the SD card. What should you check?
    Tell customer his os is corrupt and he needs to reinstall
    Flash the BIOS
    Make sure the boot order is set accordingly


    (19)
    Choose All That Apply
    A PowerEdge R200 displays a yellow-yellow-green-yellow diagnostic LED code, where can you go to to find more information to troubleshoot this issue.
    Tell the customer that error message is normal.
    dcse.dell.com
    Support.dell.com


    (20)
    Multiple Choice
    How does the depth dimension (in terms of how far does it go into a 24U or 42U rack) of the CR100 Compare to the PE R200?
    reduced
    it is the same as the PowerEdge R200
    increased


    (21)
    Multiple Choice
    What is the minimum number of drives needed to create a RAID 6?
    2
    6
    8
    4 ***


    (22)
    Multiple Choice
    You are onsite to replace optical drive on Jamie’s PowerEdge R900 system. He states that the system was working fine until this morning and now it is reporting error E2011 on the LCD Status screen on the front of the system. Select all of the options below where you could go to find information that could help you solve the problem.
    support.dell.com
    Tell the customer that the system is running normally.
    dcse.dell.com


    (23)
    Choose All That Apply
    Which of the following are required actions when removing a optical drive from the PowerEdge T105?
    Push the sliding plate lever towards the base of the computer.
    ****Remove the computer cover.
    Rotate the hard-drive carrier to the service position.
    Remove the front bezel assembly. ****


    (24)
    True or False
    The PowerEdge R905 server contains an internal SD Card socket on the system board for use with Vmware ESX embedded virtualization software.
    True
    False


    (25)
    Multiple Choice
    You are asked to replace a PEM (Porcessor Expansion Module) Riser on a PowerEdge R905, which steps below must be performed before replacing the PEM Riser?
    Remove the four front system fans
    Remove all of the expansion cards
    Turn off the system, including any peripherals and disconnect the system from the electrical outlet.
    Remove the Processor Expansion Module
    Remove the system cover


    (26)
    Choose All That Apply
    You are attempting to boot to a CD in the optical drive on a PowerEdge R200, however the system boots straight to the hard disk drive. Which options below would assist you in troubleshooting this issue?
    Ensure the optical drive is seen in the BIOS
    Presss F12 at the Dell P.O,S.T. screen to set the boot option
    Check the book sequece in the BIOS to ensure that the optical drive is set first.

    (27)
    Multiple Choice
    Which diagnostic indicator on the PowerEdge T605 will help troubleshoot issues during POST?
    BIOS status messages
    LCD status messages
    Quad pack diagnostic LEDs on the back of the system


    (2
    Multiple Choice
    On the PowerEdge T605, which keystroke should the user press during POST to access the BMC/DRAC 5 BIOS?
    F2 ****
    CTRL-S
    CTRL-R
    CTRL-E


    (29)
    Multiple Choice
    A customer says that when he turns on his system he gets the following error on POST, “Alert! Redundant memory disabled! Memory configuration does not support redundant memory.” Which one of the options below is a possible cause of this error message?
    The memory configuration does not support node interleaving. The system will run but with reduced functionality.
    A spare rank event occurred during the previous boot.
    Redundant memory was set to enable in CMOS, but the current configuration does not support redundant memory.
    Faulty or improperly installed memory modules.


    (30)
    Multiple Choice
    If you are using the Trusted Platform Module (TPM) with an encryption application such as BitLocker drive encryption, when replacing the system board you must supply ________ when you restart your system or application before you can access the encrypted data on your hard drive(s).
    the trusted USB key
    the Dell Master TPM recovery password
    a local Administrator password
    the TPM recovery key


    (31)
    The Trusted Platform Module (TPM) is designed to:
    Authenticate trusted users
    Encrypt usernames and system logins
    Secure end to end network communication
    Serve as a cryptographic foundation to a trusted environment




    (32)
    Multiple Choice
    After replacing the system board on R805, the system reports a boot failure. The customer informs you that they boot from the SD card. What should you check?
    Make sure the boot order is set accordingly
    Flash the BIOS
    Tell customer his os is corrupt and he needs to reinstall


    (33)
    Multiple Choice
    Steve is unable to boot from the CD-ROM drive on his PowerEdge R805. He needs to reseat the cable. Where does the CD-ROM plug into?
    The CD-ROM plugs directly into the IDE controller on the planar.
    The CD-ROM plugs into the daughter card.
    The CD-ROM plugs directly into the SATA controller on the planar.
    The CD-ROM plugs into an optional PCIe card.


    (34)
    Multiple Choice
    Stephanie wants to install an optional DRAC5 card on her PowerEdge R805. She wants to know what slot to install the card in. Where should it be installed?
    RAC_CONN1 and RAC_CONN2 connectors on the system board.
    Slot 1
    Slot 2
    Slot 3


    (35)
    Multiple Choice
    To remove and replace the DRAC (Dell Remote Access Controller) on the PowerEdge R900, which component must be removed form the system first?
    The processors
    Memory Risers
    The Expansion Riser


    (36)
    Multiple Choice
    You are onsite to replace some parts for Richard’s PowerEdge R900 server. The system is currently in a no P.O.S.T. state. You need to remove some components to get the server down to its base configuration. The server was purchased with 4 processors, and to get the server to its base configuation, also known as its minimum to P.O.S.T. configuration you need to remove all but one processor. Which Processor should you keep?
    The processor in socket 3
    The processor in socket 1
    The processor in socket 2
    The processor in socket 4


    (36)
    Multiple Choice
    You are onsite to replace optical drive on Jamie’s PowerEdge R900 system. He states that the system was working fine until this morning and now it is reporting error E2011 on the LCD Status screen on the front of the system. Select all of the options below where you could go to find information that could help you solve the problem.
    Tell the customer that the system is running normally.
    support.dell.com
    dcse.dell.com


    (37)
    Multiple Choice
    Which PowerEdge R905 BIOS setting must be disabled to allow Non-Uniform Memory Access?
    Uniform Memory Access
    Memory Arch Function
    NUMA
    Node Interleaving


    (3
    Multiple Choice
    What keys must be pressed during post on the PowerEdge R905 server module as the SAS 6 i/R is recognized, to enter the configuration utility?
    Ctrl and C
    Ctrl and X
    Ctrl and M
    Ctrl and A


    (39)
    Multiple Choice
    The asset tag utility should be used to set the service tag on a PowerEdge T605 when:
    Replacing the system board
    Replacing both hard-disk drives
    Replacing the processors
    A BIOS flash fails


    (40)
    Multiple Choice
    What RAID levels are supported by PERC6 controllers?
    0, 1, 6, and 60
    0, 1, 5, 10 and 50
    0, 1, 5, 6, 10, 50, and 60
    0, 1, 5, and 10 ****


    (41)
    Multiple Choice
    What is the minimum number of drives needed to create a RAID 6?
    8
    6
    2
    4 ****


    (42)Multiple Choice
    Which of the following is true about migrating virtual disks between PERC6 controllers and PERC5 controllers?
    All virtual disks created on either set of controllers can be migrating to the other set of controllers.
    All virtual disks created on a PERC5 can be migrated to a PERC6.
    All virtual disks created on a PERC6 can be migrated to a PERC5.
    (43)
    Multiple Choice
    How many drives can a RAID 6 lose before failing?
    3
    4
    1
    2***

المواضيع المتشابهه

  1. ممكن مساعدة في حل اسئلة DELL dcse server v10 certification
    بواسطة 999_ في المنتدى الأرشيف
    مشاركات: 1
    آخر مشاركة: 22-02-2010, 14:56
  2. ممكن مساعدة أين أجد هذه الشاشة Dell SP2309W في مصر
    بواسطة honor في المنتدى الأرشيف
    مشاركات: 6
    آخر مشاركة: 06-06-2009, 02:38
  3. ممكن مساعدة في حل اسئلة DELL dcse server v10 certification
    بواسطة 999_ في المنتدى منتدى الشهادات العام
    مشاركات: 0
    آخر مشاركة: 29-05-2009, 23:02
  4. ممكن مساعدة في تنصيب Project Server
    بواسطة fanksha في المنتدى الأرشيف
    مشاركات: 2
    آخر مشاركة: 20-02-2008, 19:09
  5. ممكن مساعدة في DELL INSPIRON
    بواسطة toto2648 في المنتدى الأرشيف
    مشاركات: 4
    آخر مشاركة: 03-11-2006, 15:02

الكلمات الدلالية لهذا الموضوع

المفضلات

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •