السلام عليكم و رحمة الله و بركاته
عيدكم مبارك تقبل الله منا و منكم الطاعات و صالح الاعمال
فضلا هل الحرارات دى طبيعية و ما مدى القابلية لكسر سرعة هذا الاحمق
و هذه الحرارة بعد الضغط بـ 5 دقائق
هذا على المشتت الافتراضى و جارى الاعداد لشراء مشتت احترافى
فضلا فى احد المواقع وجدت هذه الاعدادات لكسر المعالج و نفس اللوحة الام فارجو من احد المحترفين ان يترجم ما فيها و مدى ملائمتها لى
اشكركم جميعا على المساعدةكود:Advanced CPU Features: CPU Clock Ratio ................................ [19x] Intel(R) Turbo Boost Tech .................. [Enabled] CPU Cores Enabled ............................ [All] CPU Multi Threading .......................... [Enabled] CPU Enhanced Halt (C1E) ................... [Disabled] C3/C6/C7 State Support .................... [Disabled] CPU Thermal Monitor ......................... [Enabled] CPU EIST Function ............................ [Disabled] Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs Bi-Directional PROCHOT ..................... [Enabled] Uncore & QPI Features: QPI Link Speed .............................. x36 Uncore Frequency .......................... 16-18 (Always 2x memory Multi or 2x +1, 2x +2, ect) Isonchronous Frequency ..................[Enabled] Standard Clock Control: Base Clock (BCLK) Control ................ [Enabled] BCLK Frequency (MHz) ..................... 190 PCI Express Frequency (MHz) ........... [100] C.I.A.2 [Disabled] Advanced Clock Control: CPU Clock Drive ..............................[800mV] PCI Express Clock Drive ................... [900mV] CPU Clock Skew ............................. [0ps] IOH Clock Skew ............................. [0ps] Advanced DRAM Features: Performance Enhance ...................... [Standard] Extreme Memory Profile (X.M.P) ......... [Disabled] System Memory Multiplier (SPD) ........ [8x ] = 1520Mhz DRAM Timing Selectable (SPD) .......... [Manual] Channel A + B + C Channel A Timing Settings: ##Channel A Standard Timing Control## CAS Latency Time ......................8 tRCD .......................................8 tRP .........................................8 tRAS .......................................24 Below values may be left in Auto if you like, generally this is fine. For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread ##Channel A Advanced Timing Control## tRC ........................................ Auto (Should be = tRAS + tRP or above for stability) tRRD ....................................... Auto tWTR ...................................... Auto (Must be Write to Read Delay/Same Rank - (tWL + 4) tWR ........................................ Auto 5-12 (Odd # values likely will fail) tWTP ....................................... Auto (tWTP Must = tWR + tWL + 4) tWL ........................................ Auto (tWL Must be CAS Latency -1) tRFC ....................................... Auto tRTP ....................................... Auto tFAW ...................................... Auto Command Rate (CMD) ................ 1 ##Channel A Misc Timing Control## Round Trip Latency ................... Auto Advanced Voltage Control: CPU Load Line Calibration ................. [Disabled] << Enabled CPU Vcore ............................... All up to your CPU, do not use Auto. Maybe 1.25-1.4 QPI/VTT Voltage 1.150v ............ 1.28-1.35+ (Some CPU's need 1.35-1.45+, and of course higher QPI above will need more here as well) CPU PLL 1.800v ....................... 1.8-1.84 MCH/ICH PCIE 1.500v ........................... 1.5 QPI PLL 1.100v ....................... 1.14-1.24 (Auto may work fine for you) IOH Core 1.100v ..................... 1.14-1.24 ICH I/O 1.500v ....................... 1.5-1.58 (See below) ICH Core 1.1v ........................ 1.14-1.2 (on the higher end if you have many drives or larger GFX Cards) DRAM DRAM Voltage 1.500v .............. 1.64-1.66 (Some BIOS 1.64 is about 1.63 so you may need 1.66) DRAM Termination 0.750v [AUTO] Ch-A Data VRef. 0.750v [AUTO] Ch-B Data VRef. 0.750v [AUTO] Ch-C Data VRef. 0.750v [AUTO] Ch-A Address VRef. 0.750v [AUTO] Ch-B Address VRef. 0.750v [AUTO] Ch-C Address VRef. 0.750v [AUTO]
المفضلات