النتائج 1 إلى 3 من 3

الموضوع: مشكله كبيره فى ال No Password recovery

  1. #1
    عضو
    تاريخ التسجيل
    Aug 2009
    المشاركات
    200
    معدل تقييم المستوى
    0

    Arrow مشكله كبيره فى ال No Password recovery



    السلام عليكم يا اخوان ,,,

    فى عندى مشكله كبيره يريت لو حد من اخوانى يبادر و يساعدنى فى الرد يريت لو الان على طول

    المشكله كالاتى :

    انا معايا روتر وفى واحد عامل عليه باسوورد وكمان عامل enable No password recovery يعنى مانع انى

    اعرف اعمله Password recover واانا عمال براسل سيسكو والحل اللى اديهولى كلالتى

    قالولى ادوس Break بعد Image decompression لمده خمس ثوانى وانا بعمل كدا لكن مفيش نتيجه والحل

    بالتفصيل زى ما بعتهولى اهو

    Recovering a Device

    To recover a device once the No Service Password-Recovery feature has been enabled, press the Break key within 5 seconds after the image decompresses during the boot. You are prompted to confirm the Break key action. When you confirm the action, the startup configuration is erased, the password-recovery procedure is enabled, and the router boots with the factory default configuration.
    If you do not confirm the Break key action, the router boots normally with the No Service Password-Recovery feature enabled.
    Examples

    This section provides the following examples of the process:
    Confirmed Break
    Unconfirmed Break
    Confirmed Break
    PASSWORD RECOVERY FUNCTIONALITY IS DISABLED
    program load complete, entry point: 0x80013000, size: 0x8396a8
    Self decompressing the image : ################################################## ####################
    ################################################## #################### [OK]
    !The 5 second window starts now.


    telnet> send break
    telnet> send break
    telnet> send break


    Restricted Rights Legend


    Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.


    Cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706


    Cisco IOS Software, C831 Software (C831-K9O3SY6-M), Version 12.3(YA
    Copyright (c) 1986-2004 by Cisco Systems, Inc.
    Compiled Fri 13-Aug-04 03:21
    Image text-base: 0x80013200, data-base: 0x81020514


    PASSWORD RECOVERY IS DISABLED.


    Do you want to reset the router to factory default configuration and proceed [y/n] ?
    !The user enters "Y" here.


    Reset router configuration to factory default.


    This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption.


    Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.


    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html


    If you require further assistance please contact us by sending email to export@cisco.com.


    Cisco C831 (MPC857DSL) processor (revision 0x00) with 46695K/2457K bytes of memory.
    Processor board ID 0000 (1314672220), with hardware revision 0000 CPU rev number 7
    3 Ethernet interfaces
    4 FastEthernet interfaces
    128K bytes of NVRAM.
    24576K bytes of processor board System flash (Read/Write)
    2048K bytes of processor board Web flash (Read/Write)


    --- System Configuration Dialog ---


    Would you like to enter the initial configuration dialog? [yes/no]: no
    !Start up configuration is erased.


    SETUP: new interface FastEthernet1 placed in "up" state
    SETUP: new interface FastEthernet2 placed in "up" state
    SETUP: new interface FastEthernet3 placed in "up" state
    SETUP: new interface FastEthernet4 placed in "up" state


    Press RETURN to get started!


    Router>
    Router> enable
    Router# show startup configuration


    startup-config is not present


    Router# show running-config | incl service


    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption


    !The "no service password-recovery" is disabled.

    Recovering a Device

    To recover a device once the No Service Password-Recovery feature has been enabled, press the Break key within 5 seconds after the image decompresses during the boot. You are prompted to confirm the Break key action. When you confirm the action, the startup configuration is erased, the password-recovery procedure is enabled, and the router boots with the factory default configuration.
    If you do not confirm the Break key action, the router boots normally with the No Service Password-Recovery feature enabled.
    Examples

    This section provides the following examples of the process:
    Confirmed Break
    Unconfirmed Break
    Confirmed Break
    PASSWORD RECOVERY FUNCTIONALITY IS DISABLED
    program load complete, entry point: 0x80013000, size: 0x8396a8
    Self decompressing the image : ################################################## ####################
    ################################################## #################### [OK]
    !The 5 second window starts now.


    telnet> send break
    telnet> send break
    telnet> send break


    Restricted Rights Legend


    Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.


    Cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706


    Cisco IOS Software, C831 Software (C831-K9O3SY6-M), Version 12.3(YA
    Copyright (c) 1986-2004 by Cisco Systems, Inc.
    Compiled Fri 13-Aug-04 03:21
    Image text-base: 0x80013200, data-base: 0x81020514


    PASSWORD RECOVERY IS DISABLED.


    Do you want to reset the router to factory default configuration and proceed [y/n] ?
    !The user enters "Y" here.


    Reset router configuration to factory default.


    This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption.


    Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.


    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html


    If you require further assistance please contact us by sending email to export@cisco.com.


    Cisco C831 (MPC857DSL) processor (revision 0x00) with 46695K/2457K bytes of memory.
    Processor board ID 0000 (1314672220), with hardware revision 0000 CPU rev number 7
    3 Ethernet interfaces
    4 FastEthernet interfaces
    128K bytes of NVRAM.
    24576K bytes of processor board System flash (Read/Write)
    2048K bytes of processor board Web flash (Read/Write)


    --- System Configuration Dialog ---


    Would you like to enter the initial configuration dialog? [yes/no]: no
    !Start up configuration is erased.


    SETUP: new interface FastEthernet1 placed in "up" state
    SETUP: new interface FastEthernet2 placed in "up" state
    SETUP: new interface FastEthernet3 placed in "up" state
    SETUP: new interface FastEthernet4 placed in "up" state


    Press RETURN to get started!


    Router>
    Router> enable
    Router# show startup configuration


    startup-config is not present


    Router# show running-config | incl service


    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption


    !The "no service password-recovery" is disabled.

  2. #2
    عضو الصورة الرمزية hu_waly
    تاريخ التسجيل
    Oct 2006
    المشاركات
    151
    الدولة: Egypt
    معدل تقييم المستوى
    0

    رد: مشكله كبيره فى ال No Password recovery

    ال انا اعرفه اخى ان هذه الطريقة هى العادية لاسترجاع الباسورد
    ولكن مع تعطيل الخاصية no service recovery
    وانه عند تفعيل هذه الخاصية لا يمكن استرجاع الباسورد او الدخول على الرومن مود لانه بيغلق اى سي معين
    وكان الحل هو ارسال الجهاز لسيسكو وهم بيغيرو ال اى سي في الراوتر
    هذه معلوماتى ولم اجربها من قبل
    والله اعلم
    تمنياتى لك بالتوفيق
    أتمني من الله ألعلي القدير أن يوفقني إلى ما يحبة ويرضاه
    أتمني دعوة صالحة من الجميع وشكرا لكم
    ابتسم تبتسم لك الدنيا ولا تجعلها اخر همك :)
    Hu_Waly
    CCNA-Certified-
    CCNA Security-In Progress-

  3. #3
    عضو
    تاريخ التسجيل
    Mar 2008
    المشاركات
    270
    معدل تقييم المستوى
    0

    رد: مشكله كبيره فى ال No Password recovery



    طيب مفيش حجر ساعه فى الرواتر ولا حاجه ممكن تشيله أعتقد ممكن يكون متخزن عليه تفعيل الامر ده

    أنا بصراحه عمرى ما جربت ولا مسكت رواتر لسه بس ممكن يكون زى pc لم بتشيل حجر الساعه الباسورد بيروح بتاع الوندوز

    جرب كده شيله شويه وحطه تانى أو حط واحد غير وجرب كده

المواضيع المتشابهه

  1. Password Recovery
    بواسطة م/ أحمد بخيت في المنتدى الأرشيف
    مشاركات: 8
    آخر مشاركة: 03-03-2014, 15:55
  2. مشكله كبيره No password recovery
    بواسطة diligent1 في المنتدى الأرشيف
    مشاركات: 8
    آخر مشاركة: 05-10-2010, 07:08
  3. password recovery ب GNS
    بواسطة scofild2 في المنتدى الأرشيف
    مشاركات: 4
    آخر مشاركة: 04-02-2009, 08:13

المفضلات

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •