[SIZE=3][COLOR=red]الحــــر يعـــرف مــــــا تــريـــد المحـــــــكمة [/COLOR][/SIZE]
[SIZE=3][COLOR=red]وقضــــاتها سلفا قـــــد ارتشفوا من دمــــه [/COLOR][/SIZE]
[SIZE=3][COLOR=red]لا يرتجي دفعا لبهتــــــان رماه به الطغــــاة [/COLOR][/SIZE]
[SIZE=3][COLOR=red]المجرمون الجالسون فوق كراسي القضاة[/COLOR][/SIZE]
أخواني
هل من أحد ينضم لي في عمل مجموعة لدراسة CCIEV Lab من حيث:
- وضع استراتيجية للمذاكرة
- اختيار matrials ومتابعتها
- تطبيق اللابات اسبوعيا ومناقشتها دورياً
- أنا الآن أتابع فيديوهات شركة INE وأطبقها جزئياً على vmware and gns3
بعد الانتهاء من الفيديوهات يوجد كتابين من نفس الشركة لتطبيق سيناريوهات كاملة وهذه لابد لها من تأجير لاب أون لاين. وكما ذكرت من قبل فنفس الشركة تقدم هذه الخدمة باسعار غاية في الروعة.
- بعد ذلك يمكننا الاشتراك في شراء مجموعة كتب ccievoicelabs (لأنها ليست مجانية ولا يمكن الحصول عليها الا بالشراء) وميزة هذه المجموعة أن السيناريوهات التي بها قريبة بنسة 90% من الامتحان الحقيقي بشهادة الذين دخلوا الامتحان.
- تخطيطي بعد ذلك حضور Bootcamp وأشهر واحد لقيت له سمعته من شركة winnet بكندا مع المحاضر Harith
- أخير التوكل على الله ودخول الامتحان.
يا ليت ألاقي استجابة منكم لأنكم عارفين ان المجموعة هتشجع بعد أكتر
بالتوفيق للجميع
بارك الله فيك أخي hunter2005
صراحة لم اخطط لدخول الاختبار الآن
ولكن أخطط لدراسة ال CCIE voice lab كمهارات ترفع من مستواي وإلا سأنسى ما عرفته في CCVP
لذلك أنا على الاستعداد للمشاركة معكم بإذن الله حسب ما ترونه مناسبًا
إذا كانت لديك استراتيجية للمذاكرة فتقدم مشكورًا بوضعها
ربنا يوفقك
يا اخواني هل اللاب غالي مثلا .. انا بالنسبة للراكات او الروت اكسس مافي منو فائدة لانو المشاكل مو فيزكلي
انا عندي صاحبي اشترى اكتر من 200 لاب رموت اكسس ما استفاد شي ..وانا مشان هيك جبت لاب فزيكل
وبعدين GNS3 مو متل الفيزكل لاب ..
وشكرا
ربنا يوفقك
هو أكيد الفيزيكال هيفيدك أكثر وهتسمع رنات التليفونات وترد على نفسك وتبعث رسائل وتسمعها يعني مفيد جدًا( في ال ريموت عملوا حلول لهذه الأشياء ولكن صراحة الفيزيكال أقوى )
ولكن أيضًا امتحان ال CCIE سيكون remote access
في النهاية أخي كل واحد بيحسبها حسب قدرته المادية ومدى استفادته
لذلك استغل هذا اللاب جيدًا وربنا يبارك لك فيه
ولما تخلص ال CCIE ممكن تستغله في CCIE جديدة أو ممكن تبيعه
يعني مفيش خسارة لك إن شاء الله
أما بالنسبة للسعر فمكن تشوف أسعار الأجهزة على هذا الموقع
https://shop.ebay.com/?_from=R40&_tr...All-Categories
المقالة التالية مقتبسة للهاردوير المطلوب للاصدارة 3 مع الاسعار وطبقاَ للمقال ، فالتكلفة الاجمالية في حدود العشرة آلاف دولار
Updated: June 2009
You will find below the new Voice Lab Blueprint (version 3) that will be implemented mid-July 2009.
Voice Lab 3.0 Equipment and Software Versions
You should arrange access to the equipment listed below,
Lab Equipment
• Cisco MCS-7845 Media Convergence Servers
• Cisco 3825 Series Integrated Services Routers (ISR)
• Cisco 2821 Series Integrated Services Routers (ISR)
• ISR Modules and Interface Cards
- VWIC2-1MFT-T1/E1
- PVDM2
- HWIC-4ESW-POE
- NME-CUE
• Cisco Catalyst 3750 Series Switches
• IP Phones and Soft Clients
Software Versions
Any major software release which has been generally available for six months is eligible for testing in the Voice Lab Exam.
• Cisco Unified Communications Manager 7.0
• Cisco Unified Communications Manager Express 7.0
• Cisco Unified Contact Center Express 7.0
• Cisco Unified Presence 7.0
• Cisco Unity Connection 7.0
• All routers use IOS version 12.4T Train.
• Cisco Catalyst 3750 Series Switches uses 12.2 Main Train
Network Interfaces
• Fast Ethernet
• Frame Relay
Telephony Interfaces
• T1
• E1
am not saying not to follow what Cisco has laid out, hey if you can afford it by all means do so. Unfortunately I am not one of them.
Let’s go over the lab one more time. If you were to follow the topologies from all the vendors you will see the consensus being using 4 routers instead of three. So let’s break it down:
Router-1 HQ :
This is going to be the bad ass router, because it will connect the unified servers to the physical network. That’s were Cisco wants the 3825 to be.
I would recommend using a 1760, 2620XM or a 3640. Now remember this router connects to the Pstn and branch routers using FR and T1. For Frame Relay you will need a WIC-1T card and for T1 you will need a VWIC-1MFT-T1.
This router then connects to a switch which connects to the servers and the phones.
Network Modules needed:
1760 Router : Will need a PVDM (for dsps), a WIC-1T and a VWIC-1MFT-T1.
2620xm Router: Will need PVDM, a WIC-1T and a VWIC-1MFT-T1. For the VWic card it will require an addition NM module.
3640 Router: Will need PVDM, a WIC-1T and a VWIC-1MFT-T1. For the VWic card it will require an addition NM module.
Costs (from ebay approx with shipping) :
Cisco 1760-v with PVDMs = $90
Cisco 2620xm = $100
Cisco 3640 = $90
WIC-1T = $50
VWIC-1MFT-T1 = $75
NM Module = $40
So the Hq router will cost you around: $ 220.00
Router-2 PSTN :
This router is going to be the gatekeeper and the PSTN. Same as the HQ router it will need to be equipped to handle frame relay and T1.
This router will act as the T1 switch (hence the name PSTN) all of the routers will connect to this router for T1 termination. It will also connect to an analog phone. So let’s see what we will need.
Network Modules needed:
1760 Router : Will need a PVDM (for dsps), a WIC-1T and a VWIC-2MFT-T1. An FXS card.
2620xm Router: Will need PVDM, a WIC-1T and a VWIC-2MFT-T1. For the VWic card it will require an addition NM module. An FXS card
3640 Router: Will need PVDM, a WIC-1T and a VWIC-2MFT-T1. For the VWic card it will require an addition NM module. An FXS card
Note: If you are using four routers then you will need 2 VWIC-2MFT-T1 cards that will give you a total of 4 T1 ports.
Costs (from ebay approx with shipping) :
Cisco 1760-v with PVDMs = $90
Cisco 2620xm = $100
Cisco 3640 = $90
WIC-1T = $50
VWIC-2MFT-T1 = $120
NM Module = $40
FXS Card = $40
The PSTN router will cost you around: $ 390.00
Router-3 & 4 Branch :
Branch routers may perform as an SRST. So they need to be voice capable. And the will connect to the HQ and the PSTN thru frame relay and T1.
Network Modules needed:
1760 Router : Will need a PVDM (for dsps), a WIC-1T and a VWIC-1MFT-T1.
2620xm Router: Will need PVDM, a WIC-1T and a VWIC-1MFT-T1. For the VWic card it will require an addition NM module.
3640 Router: Will need PVDM, a WIC-1T and a VWIC-1MFT-T1. For the VWic card it will require an addition NM module.
Costs (from ebay approx with shipping) :
Cisco 1760-v with PVDMs = $90
Cisco 2620xm = $100
Cisco 3640 = $90
WIC-1T = $50
VWIC-1MFT-T1 = $75
NM Module = $40
The Branch routers will cost you around: $ 220.00
Frame Relay Switch :
You have two choice here:
Cisco 2522 : It has built-in serial ports no extra hardware needed.
Cisco 3640 : You will need an NM-4T network Module.
[I] Costs (from ebay approx with shipping) :
Cisco 2522 = $225
Cisco 3640 = $90
NM-4T = $50
Switches :
Well here is what your imagination can run wild. But I would recommend getting at least a 3500 series POE switch.
Cisco 3550 PWR = $100
Ip phones :
As I said earlier you will need at least 6 ip phones and a couple of analog phones. 7940 and 7960s should be good enough. They cost between $50 and a $100. Analog phones could go for as low as $10 each.
[I] Costs (from ebay approx with shipping) :
Ip phones (average) 6 @ $75 = $450
Analog Phones (w/ caller-Id) 2 @ $10 = $20
So let’s get down the bigger numbers. As you can see it is safe to assume that a CCIE voice physical lab (excluding the Unified appliances server) will cost you around:
(3 Routers + 2 Switches + 8 Phones) = $ 1700 (at the lowest end ) and close to $3000 at the highest end.
--------------------------------------------
personally i perfer setup my own lab and so far i spent around 5000 on my hardwares,
(HQ)ISR 2811(C2800NM-IPVOICEK9-M) 256/768 + VWIC-2MFT-T1 + PVDM2-16
(BR1)ISR 2811(C2800NM-ADVENTERPRISEK9-M) 64/256 + VWIC-2MFT-T1 + PVDM2-32
(PSTN)Router 3725 64/128 + NM-HDV-2T1-24
Switch 3750 POE
Switch 3500 XL + 2900XL
5 * 7961G ip phones
VMwares;
UCM 8.0 PUB + SUB
Unity Connection 8.0
Presense 8.0
Contact Center 8.0
I am planning to buy another 2811/2821 for BR2, a 3560 POE switch and plus two 7961 phones,
Total would be around 10K i think.
Actually I learnt a lot hands on experence by setting up and configing my voice lab(modules, hardware limitations, DSP and etc)
hope this helps,
Jason
وهنا تجدون ال ccie voicelab topic v3
(d-3569) CCIE Voice Lab Exam Topics v3.0
CCIE Voice Lab Exam v3.0 Topics (blueprint)
The blueprint is a detailed outline of the topics likely to appear on the lab exam. This
blueprint introduces pre-configurations of basic tasks (such as phone registration, basic
application integration, basic dial plan, etc.), in order to devote additional focus on expert
level skills (advanced configuration and troubleshooting) assessments. As usual, knowledge
of troubleshooting is an important skill and candidates are expected to diagnose and solve
issues as part of the CCIE lab exam. The topics listed are guidelines and other relevant or
related topics may also appear.
1.00 Implement and Troubleshoot Campus
Infrastructure and Services
1.01 VLAN
1.02 DHCP
1.03 TFTP
1.04 NTP
2.00 Implement and Troubleshoot CUCM
Endpoints
2.01 CUCM SCCP Endpoints
2.02 CUCM SIP Endpoints
3.00 Implement and Troubleshoot CUCME
Endpoints
3.01 CUCME SCCP Endpoints
3.02 CUCME SIP Endpoints
4.00 Implement and Troubleshoot Voice
Gateways
4.01 T1/E1 PRI
4.02 T1/E1 CAS
4.03 H.323
4.04 MGCP
4.05 SIP
4.06 H.323 RAS
4.07 IP-IP Gateway/CUBE
5.00 Implement and Troubleshoot Call Routing
Policies
5.01 Route Patterns and Dial-peers
5.02 Digit Manipulations and Translations
5.03 Class of Services
5.04 Route Selection Preference and
Redundancy
5.05 Mobility and Single Number Reach
6.00 Implement and Troubleshoot High
Availability Features
6.01 SRST
6.02 AAR
7.00 Implement and Troubleshoot Media
Resources
7.01 CODEC Selection and Flexibility
7.02 Conference Bridges
7.03 Transcoder
7.04 Music-on-hold
7.05 Media Resources Preference and
Redundancy
7.06 Other CUCM Media Resources
8.00 Implement and Troubleshoot
Supplementary Services
8.01 Call Park
8.02 Call Pickup
8.03 Barge
8.04 Callback
8.05 Other Supplementary Services
9.00 Implement and Troubleshoot Other
CUCM Voice Applications
9.01 Extension Mobility
9.02 IPMA
9.03 Other CUCM Voice Applications
10.00 Implement and Troubleshoot QoS and
CAC
10.01 L2/L3 Traffic Classifications and Policing
10.02 L2/L3 Queuing Mechanisms
10.03 L2 LFI
10.04 RSVP
10.05 Call Admission Control
11.00 Implement and Troubleshoot Messaging
11.01 Cisco Unity Connection
11.02 Cisco Unity Express
11.03 Call Handling and Routing
12.00 Implement and Troubleshoot Cisco
Unified Contact Center Express
12.01 Advanced Configuration
12.02 Script Customization
12.03 Redundancy
13.00 Implement and Troubleshoot Cisco
Unified Presence
13.01 CUCM Presence
13.02 Cisco Unified Presence Server Integration
عندى سوال للاخوه الذين يدرسون ccie سواء كانت voice او security او R & S
ما هى الطريقة التى تبداؤن بها التحضير لل written exam ؟ اعلم ان لكل شخص طريقة تناسبه فى المذاكره ولكنى بحثت كثيرا عن من نجحوا فى ccie
ينصحون اولا بدراسه كل technology على حدى
هذه من Yusuf Bhaiji المسئول عن امتحان ccie securityit is strongly recommended that you start with individual technologies and master each
topic from the blueprint independently
هل البدايه هى دراسه كل موضوع فى ال blue print على حدى وبعد ذلك مراجعه المواضيع المعقده المرتبطه بمواضيع اخرى ؟
بالنسبة لتاجير اللابات عن طريق INE فيعتبرو ارخص شركه
بس كنت عايز اضيف فايده انهم من حين لاخر بيعملو تخفيض 50% فتبقى 6 ساعات ب 7.5 دولار وده سعر خيالي
ب كل اللي عليك تعمله انك تشترك معاهم واي عرض بيعملوه هايبعتهولك على الايميل
فانت اشتري على قدر الحاجه لين متتوفق للعرض ده واشتري كميه محترمه
كذلك يا اخي hunter2005 انا في الياض وبحضر للCCIE Voice وهاتكون فكره حلوه ان احنا نعمل جروب
وشكرا
hunter2005
عضوية جديدة
السلام عليكم
اخ هانتر 2005
اهاب باشا حبيبي
ورير وحشني يا كبير
ازيكم كلكم
انا معاكم يا شباب في موضوع الCCIE Voice Lab
ياريت تراسلوني علي الخاص عشان نتواصل في المذكره والمتريل وكل ما هو مهم ومفيد
انا معاكم بأذن الله
بالتوفيق يا شباب
اخوكم
محمد عادل
-------------------------------------------
[B][SIZE=4]فين الاسئله يا شباب في اقسام Cisco
عاوزين اسئله في الVoice و الData
عاوزين نقدر نفدكم [/SIZE][/B]
[SIZE=3][COLOR=red]الحــــر يعـــرف مــــــا تــريـــد المحـــــــكمة [/COLOR][/SIZE]
[SIZE=3][COLOR=red]وقضــــاتها سلفا قـــــد ارتشفوا من دمــــه [/COLOR][/SIZE]
[SIZE=3][COLOR=red]لا يرتجي دفعا لبهتــــــان رماه به الطغــــاة [/COLOR][/SIZE]
[SIZE=3][COLOR=red]المجرمون الجالسون فوق كراسي القضاة[/COLOR][/SIZE]
السلام عليكم شباب الثورة
ahab
immdhi
هندسة العاشر
warior10
أنا سعيد جداً لتكوين هذه المجموعة ويا رب نستمر حتي نجتاز اللاب ونحصل على الشهادة. ومن يرغب في الانضمام للمجموعة فأهلا به .
وعلى بركة الله نبدأ.
في البداية أحب أن أنوه أن خبرتي في المنتديات والشات تكاد تكون معدومة.
لذا أقترح من أحد أعضاء المجموعة فتح Topicمستقل للتنوية بالموضوع ليتسنى للجميع مشاهدته والانضمام للمجموعة.
ثانياً: ما الاقتراحات التي لديكم للتواصل ومتابعة سير المذاكرة والتطبيق.
ثالثأ: يا ليت كل واحد من أعضاء المجموعة يخبرنا مدى تقدمه في اللاب وما هي ال Matrials التي يتبعها أو تتفقون أن نبدأ سوياً من البداية.
وأي أقتراحات أخرى ترونها مناسبة.
أما بالنسبة للتطبيق فعندي خطة عمل أعتقد هتكون مناسبة للجميع ان شاء الله بس خلونا نبدأ على بركة الله.
المفضلات