erase flash:

[highstyle]

أنا متشكر جدا لحضرتك وجزاك الله خيرا

[highstyle]

طب والMode هيعمل إيه بالظبط

[Gawad]

زرار المود ده علشان يدخلك علي الrommon اللي هو اسمه ap: في الاكسس بوينت

[Gawad]

Note You must use upper-case characters when you enter the IP-ADDR, NETMASK, and DEFAULT_ROUTER
options with the set command.

[highstyle]

معلش بعد إذن حضرتك زرار الmode ده مسؤل عن إيه بالظبط يعنى بيعمل Reset للاكسس ولا وظيفته إيه بالظبط

[highstyle]

أنا أسف على تكرار السؤال حدث بالغلط

[highstyle]

طب ما rommon دا إحنا بدخل عليه لما بنيجى نعمل Break password

[Gawad]

زرار المود بيعمل reset للاكسس بوينت
الrommon مش بس للباسورد لكن لما تفقد الios او تبقي damaged

Using a TFTP Server to Return to a Previous Release

---

Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Set the timeout value on the TFTP server to 30 seconds.
Step 4 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.
Step 5 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 6 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 7 Disconnect power from the access point.
Step 8 Press and hold MODE while you reconnect power to the access point.
Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 10 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 11 After the access point reboots, reconfigure it using the GUI or the CLI.

[highstyle]

معلش يا بشمهندس الفيديو فى 3 أوامل بيتكتبو فى الاول
ap: set IP_ADDR 10.0.0.11----------------------->ده IP الخاص بالاكسس بوينت

ap: set NETMASK 255.255.255.248.0-----------> ده الsubnet الخاص بالاكسس بوينت
ap: set DEFULT_ROUTER 10.0.0.10 ------------>ده الخاص بإيه بقى
لان بعدها


ap: tar -xtract tftp://10.0.0.8/c1240-k9w7-tar.124-10b.JDA3.tar flash:-------->ال IP ده خاص بالسيرفر والpc

[Gawad]

هو في المثال ده موصل جهازه والاكسس بوينت علي نفس السويتش يعني هو مش متوصل بيها دايركت
انت ممكن تخلي الdefalut_router ده نفس ايبي جهازك اللي هو في نفس الوقت الtftp server يعني خليه 10.0.0.8

[highstyle]

متشكر جدا لحضرتك