هل هناك حل لهذه المشكل Unable to control A20 line

[saidwise]

سلام عليكم ورحمة الله
ارجو من الاخوة الافاضل اصحاب الخبرة ان يساعدوني في حل هذه المشكلة لدي جهاز قديم عندما احاول ان اقوم بعملة تنصيب الوندوز 98 يعطيني الجهاز رسالة تحضير وهي على الشكل التالي :
Unable to control A20 line
وبعد ذلك تضهر هذه الرسالة
XMS driver not installed
ارجو من الاخوة مساعدتي فالموضوع في غاية الاهمية :confused:
وجزاكم الله خيرا

[محمد عبد المنعم]

عزيزي
برجاء توضيح المقصود بأن الجهاز قديم
يعني تقول مواصفاته
وشكرًا

[saidwise]

جهاز هو عبارة
HP VECTRA VL Pentium 2
350 MHZ
120 ram

[محمد عبد المنعم]

عزيزي
ها هو الحل لمشكلتك ولكنه بالإنجليزية
إذا واجهتك أي مشاكل أنا في الخدمة

The following error message is generated when the device driver HIMEM.SYS is being loaded but does not have a machine handler chosen:
ERROR: Unable to control A20 Line
There are two workarounds for this problem:• Add the /M:x switch to the HIMEM.SYS line in the CONFIG.SYS file, where x is number from the valid range of 1-14 and 16, and then restart your computer. For example: DEVICE=C:\DOS\HIMEM.SYS /M:1
Note In Microsoft Windows 98, the Himem.sys file is located in the Windows folder, not the DOS folder.

Note An incorrect handler may cause the computer to stop responding during startup. We recommend that you have an MS-DOS version 5.0 startup floppy disk available before you use different switches.
• Upgrade your computer's BIOS or contact your computer vendor for help with the modification of your CMOS settings. You may need to disable a FastGate (or similar) option.

[محمد عبد المنعم]

وهذا الحل ولكنه بتفصيل أكبر

When the computer starts, one or more of the following messages is displayed:
XMS driver: Unable to control A20 line
XMS driver not installed
HIMEM.SYS is missing
To resolve the errors, use the fololowing steps to extract HIMEM.SYS from c:\windows\options\cabs directory to the C:\windows directory:
Use one of the following methods to open a DOS prompt:
Turn on the computer and immediately press the F8 key repeatedly. From the startup menu that appears, select command prompt and press Enter.
Start the PC from the first recovery disc. From the Recover, About, and Exit screen, click Advanced Options and select Exit to DOS or DOS shell (if both choices are available, either one will work).
Insert a Windows 98 or ME startup disk and start the PC.
At the command prompt type the following:
cd c:\windows\options\cabs
Your command prompt should now look like this: c:\windows\options\cabs.
Type the following: extract /a Base4.cab himem.sys /l c:\windows.
If a message appears about overwriting a current file, enter Y to overwrite the file.
Remove the startup disk (if used) and type the following:
exit
You will now start successfully to Windows.

[saidwise]

بارك الله فيك وجزاك الله خيرا
سأعمل على تجربة هذه الحلول واسأل الله ان يكون النجاح حليفي.
شكرا جزيلا على الاهتمام اخي ابو أدهم