ياشباب مافي حد رد علي حتي الان
هو السوال صعب
شكرا لكم علي هذا المنتدي الرائع الذي اجد فيه كل ما يخص شهادة ccna
لكن اريد حل سوال vtp simulation(sw3
لانه الحل في pass4sure غير واضح (BB)
و هو السوال رقم 52 و 138 في pass4sure 372(H)
لذلك نرجو احد الاخوة الكرام ان يعطينا الحل التفصيلي لهذا السوال وخاصه الاخ الصمود او يحيي او اي احد قادر علي حل هذا السوال!Clap !Clap !Clap
ولكم جزيل الشكر
ياشباب مافي حد رد علي حتي الان
هو السوال صعب
و الله السؤال دا لفت نظرى
و مش فاهمة زيك
((((( و الله المستعان )))))
اه ،،،، السؤال محلول في الاصل بس انت اقرارة واحدة واحده
و ان شاء الله هتفهمه
hxxp://www.sadikhov.com/forum/index.php?showtopic=48534&
شرح لجواب في passe4sure
شكرا لك اخي kerouani
علي هذه الصفحه
فعلا فهي حل وافي لسؤال لكي نفهم من اين اتت الحلول في pass4sure
شكرا لك وبارك الله فيك
وهذا محتوي الصفحه
Q.1.What happens when SwX is reconnected to the network and a trunk exists between the two switches?
Step 1.Issue the Sw-AC3#show vtp status command.Note the domain name.The domain name of the 2 switches must be the same for them to exchange vtp messages
Step2:If the domain name is the same,note the config rev no of Sw-AC3 and compare with that of Sw-X.Whichever switch has higher config revision no. will be the vtp updater.Say Sw-X has higher rev no.Its vlan will replace that of Sw-AC3.
-----------------------------------------------------------------------------------------------------------------------------
Q2.What interface did switch AC-3 associate with Mac address 0010.5a0c.ffba?
Step1.Type in the command <SW-AC3#show mac-address-table.This will give you the port on which the MAC address was leant by this switch
-----------------------------------------------------------------------------------------------------------------------------
Q3.To which port of Sw-Ac3 is router VLAN-R1 connected?
Step1.Type <Sw-Ac3#show cdp neighbor detail.This will provide the details of VLAN-R1 i.e. hostname,IP address,and IOS version.
Step2:Type <Sw-AC3#cdp neighbor.This will display the port (local interface)on which R1 is connected.
-----------------------------------------------------------------------------------------------------------------------------
Q4.What ports of switch Sw-Ac3 are operationg as trunks?
Step 1.Type <Sw-Ac3#show interfaces trunk.This will display all the trunk ports.eg
Sw-AC3# show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/1 on 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/1 1-4094
Port Vlans allowed and active in management domain
Fa0/1 1-2
Port Vlans in spanning tree forwarding state and not pruned
Fa0/1 1-2
-----------------------------------------------------------------------------------------------------------------------------
Q5.Which switch is the root bridge?
Step1.Type <Sw-Ac3#show spanning-tree.This will give the MAC address of root bridge
Step2;Now type show mac-address-table.Note down associated interface with mac address of the root bridge (say fa 0/2)
Step3.Now type <Sw-AC3#show cdp neighbor.This will give the hostname of the switch connected on that port 91.e fa 0/2
----------------------------------------------------------------------------------------------------------------------------
Q6.out of which port on Sw-Ac3 will an IP packet with destination address not on local LAN be forwarded.
Step1.The packet will be sent to the default-gateway.
Step 2:Type <Sw-AC3#show cdp neighbor.This will give the local interface associated with the hostname of the router.
-----------------------------------------------------------------------------------------------------------------------------
Q7.Which Which switch is the root bridge for vlan 1?
Step 1.Type <Sw-AC3#show spanning-tree vlan 1>This will give the MAC address of root bridge
Step2;Now type show mac-address-table.Note down associated interface with mac address of the root bridge (say fa 0/2)
Step3.Now type <Sw-AC3#show cdp neighbor.This will give the hostname of the switch connected on that port 91.e fa 0/2
-----------------------------------------------------------------------------------------------------------------------------
Q8.What address should be configured as the default-gateway for the host connected to
interface Fa0/4 of Sw-AC3?
Step1.Type <Sw-AC3#show vlan.This will display list of vlans and associated port.Based on the vlan no find out the default gateway (i.e interface ip address of VLAN-R1 router corresponding to that vlan)
-----------------------------------------------------------------------------------------------------------------------------
Q9. Out of which ports will frame with source mac-address 0010.5a0c.A086 and destination mac address 000a.8a47.0612 be forwarded (choose two)
Step1.Type <Sw-AC3# show mac-address-table.
Step2.In the output check if the 2 mac addresses mentioned above have been learnt by the switch.If they are not then it will be flooded out on
all ports except the port on which it was recd (the port coressponding to source mac).If dest mac is present in the table it will be sent out on the port on which the address was learnt(port coresponding to the address in the output of show command)
-----------------------------------------------------------------------------------------------------------------------------
Q 10.From which switch did Sw-AC3 receive the VLAN information?
Step1.Type <Sw-AC3#show vtp status>
Step2.The VTP message contains updater identity i.e one who has last updated the vlan config info.The IP address of the updater will be displayed at the bottom i.e the updater of vlan info along with the time when it updated.It could also be Sw-AC3 itself.In that case the updater identity will indicate as local.
Step3.Now type <Sw-AC#show cdp neighbor detail.This will provide the hostname corressponding to that IP.
ضوابط المشاركة
المفضلات