بارك الله فيك
شكرا لك
السلام عليكم
اخوانى هذا هو حل كل اسئلة السيميوليشن بدقه قد اعدها احد اصدقائى جزاه الله خيرا
Pass4Sure
Q52:
1-
S3#sh vtp st
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 64
Number of existing VLANs : 7
VTP Operating Mode : Client
VTP Domain Name : LAB
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x98 0x76 0xE7 0xE3 0x0E 0x68 0xF5
0x3A
Configuration last modified by 10.1.10.50 at 3-1-93 00:05:02
2-
S3#sh mac-address-table
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
All 0011.5cd1.c1c0 STATIC CPU
All 0100.0ccc.cccc STATIC CPU
All 0100.0ccc.cccd STATIC CPU
All 0100.0cdd.dddd STATIC CPU
1 0011.5cd2.4505 DYNAMIC Fa0/5
2 0011.5ccc.9143 DYNAMIC Fa0/3
3 0000.1cd9.d036 DYNAMIC Fa0/3
3 0011.5ccc.9143 DYNAMIC Fa0/3
Total Mac Addresses for this criterion: 8
3-
S3#sh cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P -
Phone
Device ID Local Intrfce Holdtme Capability Platform
Port ID
S2 Fas 0/3 130 S I
WS-C2950-2Fas 0/3
vlan-R1 Fas 0/5 170 R
WS-C2950-2Fas 0/5
4-
S3#sh interface trunk
Port Mode Encapsulation Status Native vlan
Fa0/3 desirable 802.1q trunking 1
Fa0/5 desirable 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/3 1-4094
Fa0/5 1-4094
Port Vlans allowed and active in management domain
Fa0/3 1-3
Fa0/5 1-3
Port Vlans in spanning tree forwarding state and not pruned
Fa0/3 2-3
Fa0/5 1-3
5-
S3#sh spanning-tree vlan 1
VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 24577
Address 0011.5cd2.4500
Cost 19
Port 5 (FastEthernet0/5)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
Address 0011.5cd1.c1c0
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- --------
--------------------------------
Fa0/3 Altn BLK 19 128.3 P2p
Fa0/5 Root FWD 19 128.5 P2p
S3#sh cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P -
Phone
Device ID Local Intrfce Holdtme Capability Platform
Port ID
S2 Fas 0/3 159 S I WS-C2950-2Fas
0/3
S1 Fas 0/5 139 S I WS-C2950-2Fas
0/5
OR OR OR OR
S3#sh cdp neighbors detail
-------------------------
Device ID: S2
Entry address(es):
IP address: 10.1.10.5
Platform: cisco WS-C2950-24, Capabilities: Switch IGMP
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0/3
Holdtime : 172 sec
Version :
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(19)EA1c, RELEASE
SOFTWARE
(fc2)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 02-Feb-04 23:29 by yenanh
advertisement version: 2
Protocol Hello: OUI=0x00000C, Protocol ID=0x0112; payload len=27,
value=0000000
0FFFFFFFF010221FF00000000000000115CCC9140FF0000
VTP Management Domain: 'LAB'
Native VLAN: 1
Duplex: full
Management address(es):
IP address: 10.1.10.5
-------------------------
Device ID: S1
Entry address(es):
IP address: 10.1.10.50
Platform: cisco WS-C2950-24, Capabilities: Switch IGMP
Interface: FastEthernet0/5, Port ID (outgoing port): FastEthernet0/5
Holdtime : 74 sec
Version :
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(19)EA1c, RELEASE
SOFTWARE
(fc2)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 02-Feb-04 23:29 by yenanh
advertisement version: 2
Protocol Hello: OUI=0x00000C, Protocol ID=0x0112; payload len=27,
value=0000000
0FFFFFFFF010221FF00000000000000115CD24500FF0000
VTP Management Domain: 'LAB'
Native VLAN: 1
Duplex: full
Management address(es):
IP address: 10.1.10.50
Q98
1-
S3#sh vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 64
Number of existing VLANs : 7
VTP Operating Mode : Client
VTP Domain Name : LAB
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x98 0x76 0xE7 0xE3 0x0E 0x68 0xF5
0x3A
Configuration last modified by 10.1.10.50 at 3-1-93 00:05:02
>>>>>>>>>>>>If Sw-ac3 client
S3#sh cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P -
Phone
Device ID Local Intrfce Holdtme Capability Platform
Port ID
S2 Fas 0/3 177 S I WS-C2950-2Fas
0/3
S1 Fas 0/5 157 S I WS-C2950-2Fas
0/5
>>>>>>>>>> No IP add information
S3#sh cdp neighbors detail
h cdp neighbors detail
-------------------------
Device ID: S2
Entry address(es):
IP address: 10.1.10.5
Platform: cisco WS-C2950-24, Capabilities: Switch IGMP
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0/3
Holdtime : 79 sec
Version :
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(19)EA1c, RELEASE
SOFTWARE
(fc2)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 02-Feb-04 23:29 by yenanh
advertisement version: 2
Protocol Hello: OUI=0x00000C, Protocol ID=0x0112; payload len=27,
value=0000000
0FFFFFFFF010221FF00000000000000115CCC9140FF0000
VTP Management Domain: 'LAB'
Native VLAN: 1
Duplex: full
Management address(es):
IP address: 10.1.10.5
--More--
-------------------------
Device ID: S1
Entry address(es):
IP address: 10.1.10.50
Platform: cisco WS-C2950-24, Capabilities: Switch IGMP
Interface: FastEthernet0/5, Port ID (outgoing port): FastEthernet0/5
Holdtime : 168 sec
Version :
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(19)EA1c, RELEASE
SOFTWARE
(fc2)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 02-Feb-04 23:29 by yenanh
advertisement version: 2
Protocol Hello: OUI=0x00000C, Protocol ID=0x0112; payload len=27,
value=0000000
0FFFFFFFF010221FF00000000000000115CD24500FF0000
VTP Management Domain: 'LAB'
Native VLAN: 1
Duplex: full
Management address(es):
IP address: 10.1.10.50
>>>>> If SW Server
S3#sh ip interface
interface
Vlan1 is up, line protocol is up
Internet address is 10.1.10.110/24
Broadcast address is 255.255.255.255
Address determined by setup command
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is enabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is disabled
IP fast switching on the same interface is disabled
IP Null turbo vector
IP multicast fast switching is disabled
IP multicast distributed fast switching is disabled
IP route-cache flags are None
Router Discovery is disabled
--More--
Security level is default
Split horizon is enabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is disabled
IP fast switching on the same interface is disabled
IP Null turbo vector
IP multicast fast switching is disabled
IP multicast distributed fast switching is disabled
IP route-cache flags are None
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Probe proxy name replies are disabled
Policy routing is disabled
Network address translation is disabled
WCCP Redirect outbound is disabled
WCCP Redirect inbound is disabled
WCCP Redirect exclude is disabled
BGP Policy Mapping is disabled
>>>>>>>If Not SW server has update
S3#sh cdp neighbors detail
>>>>>IF SW is Transperent
Answer >>> SW (locally)
2-
S3# sh vlan
VLAN Name Status Ports
---- -------------------------------- ---------
-------------------------------
1 default active Fa0/1, Fa0/2, Fa0/4,
Fa0/6
Fa0/7, Fa0/8, Fa0/9,
Fa0/10
Fa0/11, Fa0/12, Fa0/13,
Fa0/14
Fa0/15, Fa0/16, Fa0/17,
Fa0/18
Fa0/19, Fa0/20, Fa0/21,
Fa0/22
Fa0/23, Fa0/24
2 VLAN0002 active
3 VLAN0003 active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1
Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------
------
1 enet 100001 1500 - - - - - 0
0
2 enet 100002 1500 - - - - - 0
0
3 enet 100003 1500 - - - - - 0
0
1002 fddi 101002 1500 - - - - - 0
0
1003 tr 101003 1500 - - - - srb 0
0
--More--
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1
Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------
------
1 enet 100001 1500 - - - - - 0
0
2 enet 100002 1500 - - - - - 0
0
3 enet 100003 1500 - - - - - 0
0
1002 fddi 101002 1500 - - - - - 0
0
1003 tr 101003 1500 - - - - srb 0
0
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1
Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------
------
1004 fdnet 101004 1500 - - - ieee - 0
0
1005 trnet 101005 1500 - - - ibm - 0
0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- -----------------
------------------------------------------
3-
>>>>>>> answered before
S3#sh mac-address-table
4-
>>>>>> I want the interface which on SW and connected with Router
S3#sh cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P -
Phone
Device ID Local Intrfce Holdtme Capability Platform
Port ID
S2 Fas 0/3 152 S I
WS-C2950-2Fas 0/3
vlan-R1 Fas 0/5 147 R
WS-C2950-2Fas 0/5
5-
>>>>>>> has been answered
Q 138
1- >>>has been answered
2- >>>has been answered
3- >>>has been answered
4-
>>> He want Two answer ,So SW-AC3 will flood the frame
S3#sh mac-address-table
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
All 0011.5cd1.c1c0 STATIC CPU
All 0100.0ccc.cccc STATIC CPU
All 0100.0ccc.cccd STATIC CPU
All 0100.0cdd.dddd STATIC CPU
1 0011.5cd2.4505 DYNAMIC Fa0/5
S3# sh vlan
VLAN Name Status Ports
---- -------------------------------- ---------
-------------------------------
1 default active Fa0/1, Fa0/2, Fa0/4,
Fa0/6
Fa0/7, Fa0/8, Fa0/9,
Fa0/10
Fa0/11, Fa0/12, Fa0/13,
Fa0/14
Fa0/15, Fa0/16, Fa0/17,
Fa0/18
Fa0/19, Fa0/20, Fa0/21,
Fa0/22
Fa0/23, Fa0/24
2 VLAN0002 active
3 VLAN0003 active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1
Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------
------
1 enet 100001 1500 - - - - - 0
0
2 enet 100002 1500 - - - - - 0
0
3 enet 100003 1500 - - - - - 0
0
1002 fddi 101002 1500 - - - - - 0
0
1003 tr 101003 1500 - - - - srb 0
0
2 0011.5ccc.9143 DYNAMIC Fa0/3
3 0011.5ccc.9143 DYNAMIC Fa0/3
Total Mac Addresses for this criterion: 7
>>>>>Donot forget Trunk ports
S3#sh interface trunk
Port Mode Encapsulation Status Native vlan
Fa0/3 desirable 802.1q trunking 1
Fa0/5 desirable 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/3 1-4094
Fa0/5 1-4094
Port Vlans allowed and active in management domain
Fa0/3 1-3
Fa0/5 1-3
Port Vlans in spanning tree forwarding state and not pruned
Fa0/3 2-3
Fa0/5 1-3
5- >>>>>has been answered
Q182
1-
S3#sh interface trunk
Port Mode Encapsulation Status Native vlan
Fa0/3 desirable 802.1q trunking 1
Fa0/5 desirable 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/3 1-4094
Fa0/5 1-4094
Port Vlans allowed and active in management domain
Fa0/3 1-3
Fa0/5 1-3
Port Vlans in spanning tree forwarding state and not pruned
Fa0/3 2-3
Fa0/5 1-3
2- >>>>> has been answered
3- >>>>>has been answered
4-
S3#sh arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.1.10.5 175 0011.5ccc.9140 ARPA Vlan1
Internet 10.1.10.50 176 0011.5cd2.4500 ARPA Vlan1
Internet 10.1.10.110 - 0011.5cd1.c1c0 ARPA Vlan1
OR OR OR OR
S3#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.1.10.5 176 0011.5ccc.9140 ARPA Vlan1
Internet 10.1.10.50 177 0011.5cd2.4500 ARPA Vlan1
Internet 10.1.10.110 - 0011.5cd1.c1c0 ARPA Vlan1
>>>>> If I donot find IP add , I will Ping of it
For Example>>>
S3#ping 10.1.10.50
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.10.50, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms
>>>>> then
S3#sh arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.1.10.5 179 0011.5ccc.9140 ARPA Vlan1
Internet 10.1.10.50 180 0011.5cd2.4500 ARPA Vlan1
Internet 10.1.10.110 - 0011.5cd1.c1c0 ARPA Vlan1
>>>>> I will find it
5-
S3# sh vlan
VLAN Name Status Ports
---- -------------------------------- ---------
-------------------------------
1 default active Fa0/1, Fa0/2, Fa0/4,
Fa0/6
Fa0/7, Fa0/8, Fa0/9,
Fa0/10
Fa0/11, Fa0/12, Fa0/13,
Fa0/14
Fa0/15, Fa0/16, Fa0/17,
Fa0/18
Fa0/19, Fa0/20, Fa0/21,
Fa0/22
Fa0/23, Fa0/24
2 VLAN0002 active
3 VLAN0003 active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1
Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------
------
1 enet 100001 1500 - - - - - 0
0
2 enet 100002 1500 - - - - - 0
0
3 enet 100003 1500 - - - - - 0
0
1002 fddi 101002 1500 - - - - - 0
0
1003 tr 101003 1500 - - - - srb 0
0
--More--
Good Luck
و بالنسبة لل ospf ممكن تعود للفيديو
بارك الله فيك
شكرا لك
شكرا جزيلا
مجهود رائع
جزاكم الله خيرا اخوانى
وارجوا من المشرفين ان يثبتوا هذا الموضوع نتيجة للاحتياج الكثير له
المفضلات