عندي كاميرا نوع Mercury DULXUE CLASSIC CAM و لا يمكنني التصوير إلا من خلال البطاريات

[yasernet]

عندي كاميرا من نوع Mercury DULXUE CLASSIC CAM ولاكن لا يمكنني التصوير إلا من خلال طاقة البطاريات وهذه الكاميرا تستهلك الكثير من الطاقة وقد حملت البرنامج الذي على سي دي التعريف ولكن لا يوجد به تصوير فقد تظهر لي الصورة مباشرة فهل هناك طريقة للتصوير أو برنامج؟

[adigicam]

لم افهم سؤالك بالضبط
ممكن توضح اكثر
وان امكن وصلة لموقع الكاميرا
عشان نعرف مصادر الطاقة للكاميرا

[yasernet]

أبغى أعرف هل ممكن أوصلها بالكهربة تشتغل دون بطاريات أو برنامج يعطيني نفس الوضوح الذي أصور به في البطاريات.

وهذا موقع الكاميرا:
https://www.kobian.com/products.php?productid=207

[yasernet]

هذه بعض الإسئلة وألأجوبة يمكنك تساعدك في إيجاد طريقة:
1. Can I use ATA100 on a non-ATA100 motherboard?
It is necessary to add an ATA100 add-on card for non-ATA100 motherboard.



2. Is ATA100 cable same as ATA66 cable?
Yes, both ATA100 and ATA66 cable are compatible with each other.



3. Does Linux support ATA100?
Yes, Linux is the first operating system that support ATA100.



4. What are the features of ATA100?
It is a technology on hard drive transfer speed. It can supports up to 100MB/s transfer speed and compatible with older hard drive, error correction and detection.





5. When using USB keyboard, why no keyboard present during POST and beforegetting into Windows?
First, check the connection of the USB Keyboard and motherboard. If it is correct

Press the "Delete" button when the system booting up, set enable USB keyboard in BIOS setting, then re-boot the system again and check if it is ok.

Owing to the default setting of USB keyboard support is "by OS", there is no way to use the USB keyboard before getting into Windows. We suggest users change the setting of USB keyboard support from "by OS" to "by BIOS" whenever you need to use keyboard beyond Windows environment like these,

When you want to get into the RAID or SCSI BIOS for changing some settings
When you boot from a floppy disk for BIOS flashing
The change can be done by this way.

CMOS Setup Utility -> Integrated Peripherals -> USB Keyboard Support -> BIOS



6. How should I do when memory test fail?
Usually happens on memory error. Boot the machine with only one ram module, find the module that contains error.



7. Why the primary master/slave hard disk fail?
Please check the following setting first.

1. Check the connection between the cable and hard drive is correct.

2. The power source is connected to hard drive.

3. Check the jumper setting (Master or slave) of the hard drive is correct.

4. BIOS setting



8. How Press to skip memory test when the system booting up?
Press ESC button from your keyboard to skip memory test.

If you didn't set the fast boot from BIOS setting, when machine boots up it will detect the hardware in your machine. If you don't want to wait for the hardware detection, you could press ESC to skip it or enable fast boot from BIOS setting.





9. When we should upgrade the system BIOS?
When your system is very stable, it is not necessary to upgrade your system BIOS. However, if you are having compatibility problem or can't use some of the setting on the new device then you need to upgrade your system BIOS.

Please visit our Download Page to get the latest BIOS for upgrade your system.



10. Why the parallel port not working correctly when in ECP mode?
Set the DMA setting, there is a conflict with other devices.



11. Is it necessary to get another heat sink for the chipset of motherboard?
We have designed the most suitable heat sink for chipset of our Mercury motherboard and VGA card. So, it is high performance for our product and does not require a new heat sink for our chipset.



12. What is an IrDA infrared data connection?
Infrared light (IrDA) is a cordless data connection, it is a low-cost transceiver signaling technology for data exchange.

It provides high-speed digital exchange through the typical PC UART/serial port at 9600-115200 bits/s, and in some units compatible high speed extensions up to 1Mb/s and 4Mb/s speeds.



13. How could I do when floppy disk(s) fail?
Please check the following setting first, if both is correct, then the drive may be have problem.

1. Check the cable that connected to the floppy drive and the motherboard.

2. Check the power cable that connected to the floppy drive.





14. How could I do when Hard disk(s) disagnosis fail?
It is usually occurs when hard drive failed. Please try to connect this hard drive to another computer and to see if the hard drive works or not. If the problem still occurs, the hard drive need to repair.



15. The Technological background of ULTRA DMA 33 ULTRA DMA 33
Ultra DMA "widens" the path to the hard drive by transferring twice as much data per clock cycle. The net effect is that the maximum burst data transfer rate from the disk drive increases from 16.6 Megabytes per second (MB/s) to 33 MB/s. The Ultra DMA protocol lets host computers (PCs) send and retrieve data faster, removing bottlenecks associated with data transfers -- especially during sequential operations. Users of new PCs will need less time to boot their systems and open applications, a direct result of the improved throughput provided by Ultra DMA. Bus Mastering technology can also be implemented with Ultra DMA disk drives. Similar reductions in CPU utilization will be experienced when Bus Mastering drivers are installed. In addition to speed improvements, the protocol brings new data integrity capabilities to the ATA/IDE interface. Improved timing margins and the use of Cyclical Redundancy Check (CRC), a data protection verification not implemented in legacy ATA modes, help ensure the integrity of transferred data.



16. Does DMA33 Hard drive work with DMA66 controller?
Yes, DMA33 Hard drive can work with DMA66 controller. But the hard drive will work on the lowest transfer speed, so, it can't work in DMA66 transfer speed.

[yasernet]

او هل ممكن أصور بها وأنا موصله بالكمبيوتر بطريقة البطاريات.

[yasernet]

هذا ما رأينه في الكاتلوج وعندي في أسفل الكاميرا فتحة مدورة هل هناك توصيلة كهربائية وإن كان في أرجو أن تدلني على المحل في جدة أو مكة وي أخي أنا مسجل في منتداك أرجو أن تبعتلي كود التنشيط على الرسائل الخاصة:

[adigicam]

مصدر الطاقة الخارجي ممكن يكون محول ولكن عن الفتحة التي ذكرتها هل هي لتوصيل المحول ان كان ذلك فالحصول على محول سهل فقط تأكد من السالب والموجب في الفتحة والقوة المطلوبة للطاقة او الحصول على بطاريات قابلة للشحن من نوع النيكل
المشكلة ان الموقع لا يعطي اي تفاصيل اخرى عن المواصفات التقنية

[yasernet]

ممكن تدلني عن اسم البطاريات القابلة للشحن واين اجدها وكيف اشحنها وكم مرة استطيع اعادة شحنها

[yasernet]

قرأت عن الفتحة في الكاتلوج فطلع أن الفتحة Tripod Soket أي حامل للكاميرا.

[adigicam]

هناك البطاريات NiMH القابلة للشحن والانواع الاكثر انتشارا في المنطقة السوني بقوة 1700 مع الشاحن تقريبا 90 ريال عند الوكيل وممكن شحنة الى 500 مرة تقريبا
وفي انواع ثانية موجودة في السوق امثال GP power bank مرات الشحن تصل الى 1000 مرة وانا استعملهم وممتازين جدا بس شريتهم من البحرين وما اعرف اين تتوفر عندكم بس هي اكيد متوفرة عند محلات الالكترونيات وخصوصا وكلاء الكاميرات