النتائج 1 إلى 8 من 8

الموضوع: question about e1

  1. #1
    عضو
    تاريخ التسجيل
    May 2007
    المشاركات
    466
    معدل تقييم المستوى
    0

    question about e1



    السلام عليكم ورحمة الله وبركاته

    هل هناك طريقة استطيع من خلالها معرفة أي channel مشغولة في ال e1

    يعني بطريقة مشابهة لأمر

    show ip inter br

    سوف يعرض لي كل إنتيرفيس ومنها استطيع معرفة حالة كل واحدة up or down

  2. #2
    عضو برونزي
    تاريخ التسجيل
    Mar 2007
    المشاركات
    1,529
    الدولة: Egypt
    معدل تقييم المستوى
    12

    رد: question about e1

    يعني مش فاهم اانت عايز ايه بالضبط علشان أقدر أجاوب
    يعني لو عايز تعرف حال الانترفيس عندك الامر اللي قولت عليه

    أو بقي تعمل sh run و تشوف واحد واحد
    يعني مش عارف هو ده اللي انت عايزه و لا ايه لاني اصلا مش فاهم سؤالك كويس
    Mohamed Samir
    Double CCIEs#27042 (R/S&SP)
    رابط القناة الخاص بي
    https://www.youtube.com/channel/UCn9zWk33OYX65NFdTmra6-g/playlists

  3. #3
    عضو برونزي
    تاريخ التسجيل
    May 2007
    المشاركات
    1,475
    معدل تقييم المستوى
    12

    رد: question about e1

    يتري ممكن توضح اكتر
    -------------------------------------------
    [B][SIZE=4]فين الاسئله يا شباب في اقسام Cisco
    عاوزين اسئله في الVoice و الData
    عاوزين نقدر نفدكم [/SIZE][/B]

  4. #4
    عضو
    تاريخ التسجيل
    Mar 2007
    المشاركات
    484
    معدل تقييم المستوى
    0

    رد: question about e1

    السلام عليكم
    ممكن بالأمر:
    show controllers e1
    or
    sho controllers sonet
    هيعرضلك كل المعلومات عن الكنترولر ومنا Channels state
    _____________
    Yasser Kassem

  5. #5
    عضو
    تاريخ التسجيل
    May 2007
    المشاركات
    466
    معدل تقييم المستوى
    0

    رد: question about e1

    أشكر الأخوة على الرد

    أخي ياسر أعتقد أن الأمر

    show controller conet

    يستخدم مع ال ATM وقد حاولت استخدامه إلا أني لم اجده على الراوتر

    الأمر

    show controller e1
    كنت قد قمت بتجربته إلا أنني لم أجد فيه شيء يساعد إلا إن كنت لم أفهم المحتوى بشكل جيد

    هذه نتيجة تطبيق الأمر


    VoiceGateway#show controllers e1
    E1 0/0/0 is up.
    Applique type is Channelized E1 - balanced
    Description: E1 QSIG connected to E-PBX
    No alarms detected.
    alarm-trigger is not set
    Version info Firmware: 20050620, FPGA: 15, spm_count = 0
    Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    Data in current interval (26 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    E1 0/0/1 is down.
    Applique type is Channelized E1 - balanced
    Far End Block Errors Detected
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 20050620, FPGA: 15, spm_count = 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    Data in current interval (58 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 58 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 1/0 is down.
    Applique type is Channelized E1 - balanced
    Transmitter is sending remote alarm.
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 00000000, FPGA: 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    CEIPNM specific information:
    Data in current interval (54 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 54 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 1/1 is down.
    Applique type is Channelized E1 - balanced
    Transmitter is sending remote alarm.
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 00000000, FPGA: 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    CEIPNM specific information:
    Data in current interval (56 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 56 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 1/2 is down.
    Applique type is Channelized E1 - balanced
    Transmitter is sending remote alarm.
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 00000000, FPGA: 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    CEIPNM specific information:
    Data in current interval (56 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 56 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 1/3 is down.
    Applique type is Channelized E1 - balanced
    Transmitter is sending remote alarm.
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 00000000, FPGA: 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    CEIPNM specific information:
    Data in current interval (58 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 58 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    VoiceGateway#

    ولتوضيح لسؤالي كما طلب بقية الأخوة
    عندي على السوتش مثلا 12 بورت أريد أن أعرف اي بورت داون وايها أب
    من اسهل الطرق في هذه الحالة استخدام الأمر
    show ip inter br

    في حالتي هذه أنا لا اتعامل مع بورت أنا أتعامل بورت يحوي 30 channel
    أريد أن أعرف ما هي ال channel التي يتم استخدامها أو هل هناك channel مستخدمة أو لا؟؟؟

  6. #6
    عضو
    تاريخ التسجيل
    May 2007
    المشاركات
    466
    معدل تقييم المستوى
    0

    رد: question about e1

    أعتقد اني وجدت الحل
    بس صعب أجرب الآن لأني داخل باستخدام telnet على الراوتر

    استخدمت الأمر

    show voice port

    أعطاني التالي



    PORT CH SIG-TYPE OPER STATUS STATUS TIP RING
    0/0/0: 01 isdn-voice dorm none none
    0/0/0: 02 isdn-voice dorm none none
    0/0/0: 03 isdn-voice dorm none none
    0/0/0: 04 isdn-voice dorm none none
    0/0/0: 05 isdn-voice dorm none none
    0/0/0: 06 isdn-voice dorm none none
    0/0/0: 07 isdn-voice dorm none none
    0/0/0: 08 isdn-voice dorm none none
    0/0/0: 09 isdn-voice dorm none none
    0/0/0: 10 isdn-voice dorm none none
    0/0/0: 11 isdn-voice dorm none none
    0/0/0: 12 isdn-voice dorm none none
    0/0/0: 13 isdn-voice dorm none none
    0/0/0: 14 isdn-voice dorm none none
    0/0/0: 15 isdn-voice dorm none none
    0/0/0: 17 isdn-voice dorm none none
    0/0/0: 18 isdn-voice dorm none none
    0/0/0: 19 isdn-voice dorm none none
    0/0/0: 20 isdn-voice dorm none none
    0/0/0: 21 isdn-voice dorm none none
    0/0/0: 22 isdn-voice dorm none none
    0/0/0: 23 isdn-voice dorm none none
    0/0/0: 24 isdn-voice dorm none none
    0/0/0: 25 isdn-voice dorm none none
    0/0/0: 26 isdn-voice dorm none none
    0/0/0: 27 isdn-voice dorm none none
    0/0/0: 28 isdn-voice dorm none none
    0/0/0: 29 isdn-voice dorm none none
    0/0/0: 30 isdn-voice dorm none none
    0/0/0: 31 isdn-voice dorm none none

  7. #7
    عضو
    تاريخ التسجيل
    Mar 2007
    المشاركات
    484
    معدل تقييم المستوى
    0

    رد: question about e1

    السلام عليكم
    أخى الحبيب ما قمت به هو ما اقصده انا استخدم Sonet لانها موجوده وانت استخدمت e1 لانها ماتريد
    والنتيجه موجوده فى المخرجات - لاحظ الاتى:
    VoiceGateway#show controllers e1
    E1 0/0/0 is up.
    Applique type is Channelized E1 - balanced
    Description: E1 QSIG connected to E-PBX
    No alarms detected.
    alarm-trigger is not set
    Version info Firmware: 20050620, FPGA: 15, spm_count = 0
    Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    Data in current interval (26 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    E1 0/0/1 is down.
    Applique type is Channelized E1 - balanced
    Far End Block Errors Detected
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 20050620, FPGA: 15, spm_count = 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    Data in current interval (58 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 58 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 1/0 is down.
    Applique type is Channelized E1 - balanced
    Transmitter is sending remote alarm.
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 00000000, FPGA: 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    CEIPNM specific information:
    Data in current interval (54 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 54 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 1/1 is down.
    Applique type is Channelized E1 - balanced
    Transmitter is sending remote alarm.
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 00000000, FPGA: 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    CEIPNM specific information:
    Data in current interval (56 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 56 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 1/2 is down.
    Applique type is Channelized E1 - balanced
    Transmitter is sending remote alarm.
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 00000000, FPGA: 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    CEIPNM specific information:
    Data in current interval (56 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 56 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    E1 1/3 is down.
    Applique type is Channelized E1 - balanced
    Transmitter is sending remote alarm.
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info Firmware: 00000000, FPGA: 0
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    CRC Threshold is 320. Reported from firmware is 320.
    CEIPNM specific information:
    Data in current interval (58 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 58 Unavail Secs
    Total Data (last 24 hours)
    0 Line Code Violations, 0 Path Code Violations,
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
    VoiceGateway#

    ايضا هذا الامر مفيد
    show interface desc | in down (cisco routers)
    sho interface desc | match down (Juniper routers)
    سوف يعرض البورت الداون فقط اذا كان اللاين او البروتوكول داون
    بالتوفيق
    _____________
    Yasser Kassem

  8. #8
    عضو
    تاريخ التسجيل
    May 2007
    المشاركات
    466
    معدل تقييم المستوى
    0

    رد: question about e1



    في الحقيقة اخي الذي أريده انا هو أي تشانيل من 31 تشانيل مستخدمة لحظة المكالمة
    والحل هو أحد هذين الأمرين

    show ip inter br

    or

    show voice port

    وجزاك الله خيرا على تعاونك

المواضيع المتشابهه

  1. question
    بواسطة oldtown في المنتدى الأرشيف
    مشاركات: 2
    آخر مشاركة: 21-11-2012, 23:41
  2. question about 70-680
    بواسطة prof في المنتدى منتدى الشهادات العام
    مشاركات: 1
    آخر مشاركة: 27-02-2010, 04:27
  3. mac and ip question
    بواسطة hamnon في المنتدى الأرشيف
    مشاركات: 4
    آخر مشاركة: 19-12-2009, 19:54
  4. ؟؟QUESTION؟؟
    بواسطة أبوهارون في المنتدى الأرشيف
    مشاركات: 4
    آخر مشاركة: 12-11-2005, 20:49
  5. N+ and A+ question
    بواسطة ahmedation2002 في المنتدى الأرشيف
    مشاركات: 0
    آخر مشاركة: 11-11-2005, 02:21

الكلمات الدلالية لهذا الموضوع

المفضلات

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •