question about e1

[forMyIslam]

السلام عليكم ورحمة الله وبركاته

هل هناك طريقة استطيع من خلالها معرفة أي channel مشغولة في ال e1

يعني بطريقة مشابهة لأمر

show ip inter br

سوف يعرض لي كل إنتيرفيس ومنها استطيع معرفة حالة كل واحدة up or down

[mohammedsn]

يعني مش فاهم اانت عايز ايه بالضبط علشان أقدر أجاوب
يعني لو عايز تعرف حال الانترفيس عندك الامر اللي قولت عليه

أو بقي تعمل sh run و تشوف واحد واحد
يعني مش عارف هو ده اللي انت عايزه و لا ايه لاني اصلا مش فاهم سؤالك كويس

[هندسه العاشر]

يتري ممكن توضح اكتر

[YasrKasem]

السلام عليكم
ممكن بالأمر:
show controllers e1
or
sho controllers sonet
هيعرضلك كل المعلومات عن الكنترولر ومنا Channels state

[forMyIslam]

أشكر الأخوة على الرد

أخي ياسر أعتقد أن الأمر

show controller conet

يستخدم مع ال ATM وقد حاولت استخدامه إلا أني لم اجده على الراوتر

الأمر

show controller e1
كنت قد قمت بتجربته إلا أنني لم أجد فيه شيء يساعد إلا إن كنت لم أفهم المحتوى بشكل جيد

هذه نتيجة تطبيق الأمر

VoiceGateway#show controllers e1
E1 0/0/0 is up.
Applique type is Channelized E1 - balanced
Description: E1 QSIG connected to E-PBX
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20050620, FPGA: 15, spm_count = 0
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (26 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
E1 0/0/1 is down.
Applique type is Channelized E1 - balanced
Far End Block Errors Detected
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20050620, FPGA: 15, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (58 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 58 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 1/0 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 00000000, FPGA: 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
CEIPNM specific information:
Data in current interval (54 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 54 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 1/1 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 00000000, FPGA: 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
CEIPNM specific information:
Data in current interval (56 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 56 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 1/2 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 00000000, FPGA: 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
CEIPNM specific information:
Data in current interval (56 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 56 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 1/3 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 00000000, FPGA: 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
CEIPNM specific information:
Data in current interval (58 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 58 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
VoiceGateway#

ولتوضيح لسؤالي كما طلب بقية الأخوة
عندي على السوتش مثلا 12 بورت أريد أن أعرف اي بورت داون وايها أب
من اسهل الطرق في هذه الحالة استخدام الأمر
show ip inter br

في حالتي هذه أنا لا اتعامل مع بورت أنا أتعامل بورت يحوي 30 channel
أريد أن أعرف ما هي ال channel التي يتم استخدامها أو هل هناك channel مستخدمة أو لا؟؟؟

[forMyIslam]

أعتقد اني وجدت الحل
بس صعب أجرب الآن لأني داخل باستخدام telnet على الراوتر

استخدمت الأمر

show voice port

أعطاني التالي

PORT CH SIG-TYPE OPER STATUS STATUS TIP RING
0/0/0: 01 isdn-voice dorm none none
0/0/0: 02 isdn-voice dorm none none
0/0/0: 03 isdn-voice dorm none none
0/0/0: 04 isdn-voice dorm none none
0/0/0: 05 isdn-voice dorm none none
0/0/0: 06 isdn-voice dorm none none
0/0/0: 07 isdn-voice dorm none none
0/0/0: 08 isdn-voice dorm none none
0/0/0: 09 isdn-voice dorm none none
0/0/0: 10 isdn-voice dorm none none
0/0/0: 11 isdn-voice dorm none none
0/0/0: 12 isdn-voice dorm none none
0/0/0: 13 isdn-voice dorm none none
0/0/0: 14 isdn-voice dorm none none
0/0/0: 15 isdn-voice dorm none none
0/0/0: 17 isdn-voice dorm none none
0/0/0: 18 isdn-voice dorm none none
0/0/0: 19 isdn-voice dorm none none
0/0/0: 20 isdn-voice dorm none none
0/0/0: 21 isdn-voice dorm none none
0/0/0: 22 isdn-voice dorm none none
0/0/0: 23 isdn-voice dorm none none
0/0/0: 24 isdn-voice dorm none none
0/0/0: 25 isdn-voice dorm none none
0/0/0: 26 isdn-voice dorm none none
0/0/0: 27 isdn-voice dorm none none
0/0/0: 28 isdn-voice dorm none none
0/0/0: 29 isdn-voice dorm none none
0/0/0: 30 isdn-voice dorm none none
0/0/0: 31 isdn-voice dorm none none

[YasrKasem]

السلام عليكم
أخى الحبيب ما قمت به هو ما اقصده انا استخدم Sonet لانها موجوده وانت استخدمت e1 لانها ماتريد
والنتيجه موجوده فى المخرجات - لاحظ الاتى:
VoiceGateway#show controllers e1
E1 0/0/0 is up.
Applique type is Channelized E1 - balanced
Description: E1 QSIG connected to E-PBX
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20050620, FPGA: 15, spm_count = 0
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (26 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
E1 0/0/1 is down.
Applique type is Channelized E1 - balanced
Far End Block Errors Detected
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20050620, FPGA: 15, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (58 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 58 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 1/0 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 00000000, FPGA: 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
CEIPNM specific information:
Data in current interval (54 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 54 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 1/1 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 00000000, FPGA: 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
CEIPNM specific information:
Data in current interval (56 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 56 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 1/2 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 00000000, FPGA: 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
CEIPNM specific information:
Data in current interval (56 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 56 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
E1 1/3 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 00000000, FPGA: 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
CEIPNM specific information:
Data in current interval (58 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 58 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
VoiceGateway#

ايضا هذا الامر مفيد
show interface desc | in down (cisco routers)
sho interface desc | match down (Juniper routers)
سوف يعرض البورت الداون فقط اذا كان اللاين او البروتوكول داون
بالتوفيق

[forMyIslam]

في الحقيقة اخي الذي أريده انا هو أي تشانيل من 31 تشانيل مستخدمة لحظة المكالمة
والحل هو أحد هذين الأمرين

show ip inter br

or

show voice port

وجزاك الله خيرا على تعاونك