السلام عليكم ورحمة الله وبركاتة
أولاً: جواب شكر للمنتدى العظيم عرب هاردوير
أطلب مساعدتكم لحل سؤال لمذا أظع ip default gateway ل Switch ???
فوظع ip address ل Vlan واظح لكن لم أستطع فهم صلاحية default gateway ل Switch
وشكرا
السلام عليكم ورحمة الله وبركاتة
أولاً: جواب شكر للمنتدى العظيم عرب هاردوير
أطلب مساعدتكم لحل سؤال لمذا أظع ip default gateway ل Switch ???
فوظع ip address ل Vlan واظح لكن لم أستطع فهم صلاحية default gateway ل Switch
وشكرا
السلام عليكم
أنا وجدت هذة المقالة علي صفحة الأنترنت وان شاء اللة تفيدك
Why is an Ip address and default gateway needed in the switch?
After all switches are OSI Layer 2 devices that care only about MAC addresses.
The modern switches are manageable and support extra features than normal old fashion switches. This features include the support of TCP/IP applications like ping, telnet, trace route etc. For example, if you want to telnet or ping a switch, the switch must have an Ip configured. Also, if you want to execute ping or telnet to a device in another subnet the switch must have a default gateway configured.
Now let’s see the configuration for a 2950 series cisco switch.
Ip address
To configure the ip address first you have to enter from global configuration mode to interface vlan 1.
Switch#
Switch#conf t
Switch(config)#int vlan 1
Switch(config-if)#ip address {your ip address} {mask}
Switch(config-if)#no shutdown
Default Gateway
Be careful!!! The configuration of default gateway takes place in the configuration mode and the command does not include the mask for the ip.
Switch#
Switch#conf t
Switch(config)#ip default-gateway {ip address}
Now you can access your switch remotely, you can ping it from another network with different subnet and start “playing” with the settings. Have fun
وَالَّذِينَ يَقُولُونَ رَبَّنَا اصْرِفْ عَنَّا عَذَابَ جَهَنَّمَ إِنَّ عَذَابَهَا كَانَ غَرَامًا
*****************************
من مواضيعي
الحمد اللة تم الأنتهاء من تأليف الكتاب لشرح منهج CCNA ومنهج الBCMSN لتحميل الملف اضغط علي الرابط التالي
https://www.4shared.com/dir/17764113...602/CISCO.html
والله ما شرح موضح وجميل
والموضوع متميز والسؤال كان جديد علي لاني لم افكر في موضوع البينج والتل نيت من خارج الشبكه
مما يعني ان تقدر ان تقوم بعمل telnet and ping من خارج الLan
بارك الله في واضع السؤال
وجزاه الله كل الخير علي من وجد ووضع الحل
وجزاكم جميعا كل خير
-------------------------------------------
[B][SIZE=4]فين الاسئله يا شباب في اقسام Cisco
عاوزين اسئله في الVoice و الData
عاوزين نقدر نفدكم [/SIZE][/B]
انا عندي سؤال عن switches
انا عندي tow switch عملت vlan لكل switch
مثلا في sw1 عملت vlan4 و vlan5
وفي sw2 عملت vlan4 و vlan 5
الان اريد الربط بين هذين السويتشين مثلا في sw1 : f0/1 شكبته في sw2 :0/2 الان اريد vlan4 في sw1 يستطيع
الاتصال مع vlan4 ف sw2
ماهي الاوامر لاني عملتها لكن لم تضبط معي الاوامر لا ادري هل السويتش اللذي عندي لايدعم الامر هذا او لا؟
شكرا ultraviolet2006
انا فعلا كنت بدور على اجابة للسؤال ده وكنت بناقش فيه احد الزملاء
بالنسبة لسؤال الاخ هايلوكس
يجب توصيل ال 2 switch with cross cable and make the 2 port trunk and that will make vlan4 in sw1 see vlan4 in sw2 like it in the same switch
switch(conf)#interface fastethernet 0/1
switch(conf-if)#switchport mode trunk
switch(conf-if)#switchport trunk native vlan 1
and you have make this in the 2 switch
Marc Kamel
MCT, CCNP, Cvoice, MCITP:
88888
جزاك الله خير أخوي ويوفقك .. ضبطت معي
جزاك الله خيرا وجعل ذلك في ميزان حسناتك يوم القيامة ان شاء الله
جزاك الله خير
سؤال جميل واجابة اجمل
* متى وجدت الإرادة والصبر زالت الصعاب.
* احسن وسيلة للتغلب على الصعاب اختراقها.
سؤال جميل وإجابات ممتازة ومشاركات رائعة من أحلى وأجمل اعضاء
جزاكم الله خيرا
أحبكم فى الله
ربنا يبارك فى هذا المنتدى الرااااااااااااااااااااائع
المفضلات