من أفضل المراجع التى سوف تجدها هو شرح Petr Lapukhov
https://blog.ine.com/wp-content/uplo...onvergence.pdf
و اذا احتجت أى شىء انا بالخدمة ،،
السلام عليكم
لو سمحتم اشرحولنا الفرق بين الuplink fast , backbone fast
متي بتم استخدامهم و الية عملهم وليش ما كانوا شيء و احد
من أفضل المراجع التى سوف تجدها هو شرح Petr Lapukhov
https://blog.ine.com/wp-content/uplo...onvergence.pdf
و اذا احتجت أى شىء انا بالخدمة ،،
هذا الحكي بالـ Switching ولا وين ؟؟؟؟؟
إذا ما أضعنا شامها وعراقها فتلك إذاً من البيت الحرام مداخله
نعم أخي في كورس السويتش
اللهم وفقني لحفظ القرآن
موضوعي حول ال virtualisation مع VMware
https://www.arabhardware.net/forum/s...d.php?t=215569
تعرف على شهادة الأنستركتور CCSI
https://www.arabhardware.net/forum/s...54#post1851054
UplinkFast
لو عندك فالسويتش اكثر من لينك الى root bridge
طبعا اللينك الرئيسي يسمى primary or root port والثاني يكون block port
لوا نقطع اللينك الرئيسي والي هو ال primary هذا الامر يساعد السويتش في انه يشغل الينك الثاني والي هو البلوك
في اسرع وقت , طبعا اللينك يحتاج الى 50 ثانيه علشان يشتغل بس مع هذا الامر بيشتغل في وقت اقل
BackboneFast
الامر هذا يختلف عن الامر الاول في شي واحد انه مايكتشف الانقطاع في اللينك الموصل بشكل مباشر مع السويتش لكن يكتشف الاخطا فالينك الي موصل بسويتش بعيد يعني لازم تشغل هذا الامر على كل سويتش عندك علشان يتبادلون المعلومات
بنوع من البايكت يسمى inferior BPDU من خلالها يعرف السويتش ان اللينك الي يؤدي الى root bridge قد تعطل
يعني السويتش يمكن يكون بعيد عنه ال root bridge يعني مش متصل معاه مباشر
فيه سويتش بينهم
طبعا تم دمج UplinkFast +BackboneFast +PortFast =Rapid Spanning Tree Protocol (RSTP) 802.1W
بالتوفيق
First let us differentiate between Superior & Inferior BPDU:
Superior BPDU is naturally received on RP which has the best path to the Root – from the Root Bridge.
Inferior BPDU is received on Altn Port from DB (Designated Bridge).
UplinkFast
Approximately saves the entire 50 Sec of STP convergence time
We should enable it only on switch A1 -with Altn/Blocked port
Cisco Proprietary
Beneficial upon direct topology change (BPDU includes TCN) – link failure
Enables the switch to find an alternative path (to the Root) before the primary path fails. So, if the primary link fails, the Secondary will come up swiftly without needing to wait 50 Sec.
BackboneFast
It Saves 20 Sec on STP convergence time.
We should enable it on all switches.
Cisco Proprietary
.it is beneficial upon indirect topology change ( NO TCN flag in BPDU) – the link does not work perfectly. Take heed that Superior BPDU does not reach Sw A1.
BackboneFast: is a mechanism by which each switch tells its neighbor whether another path to the root could be found. Here, Sw C2 tells Sw A1.
Suppose enabling this feature on the network. For some reason, Sw A1 dose not receive BPDU from the Root. Instead, Sw A1 receives Inferior BPDU from Sw C2.
Thereupon, the blocked port on Sw A1 moves to the listening state directly without waiting to superior BPDU to expire with max age timer 20 Sec.
I hope that has been informative
Please notice that I'm green ( inexperienced). So, it would be nice of veterans to go over this information
هلا فيك اخوي محمد وشكرا لجميع الي شاركو
بخصوص سوالك والله ماعندي فكره
يمكن اي حد من الاعضاء عنده خبره فccnp يفيدنا
موفقين ان شاء الله
الله يعطيكم العافية
إذا ما أضعنا شامها وعراقها فتلك إذاً من البيت الحرام مداخله
المفضلات