مشكلة في فك و تركيب معالج إنتل بنتيوم 3

**ayman2009** · 16-01-2008, 07:04

السلام عليكم و رحمة الله و بركاته

الكلام المكتوب تحت ده بيشرح طريقة فك و تركيب معالج بنتيوم 3 بس بصراحه مش فاهم حاجه ممكن حد يشرح بالعربي لكلام ده ؟

Pentium III processor installation steps for metal heat sink clip:

Raise the handle of the 370-pin socket.
Carefully install the processor into the 370-pin socket making sure that none of the pins are bent.
Close the handle of the socket.
Next install the fan heat sink. Make sure to install the heat sink onto the processor after the processor has been inserted into the 370-pin socket. Place the fan heat sink onto the processor so that the integrated clip lines up with the socket's attach tabs and the fan cable aligns with the PGA370 mark on the 370-pin socket.
Caution: Take care to not damage the white thermal interface pad on the bottom of the heat sink.
Locate the socket tab opposite the PGA370 mark on the socket. Latch the clip to this tab first.
To attach the clip to the other socket tab, locate a standard #1, small flathead screwdriver and align with upper clip slot (Figure 5a - 'B').

Insert screwdriver into clip slot. Extend (as shown in Figure 5a - 'D') the heat sink clip away from the socket tab (Figure 5a - 'C') by rotating the screwdriver upwards toward the fan heat sink (Figure 5a - 'A').

Continue rotating the screwdriver upwards (as shown in Figure 5b - 'A') until the bottom edge of the clip clears the socket tab (Figure 5b - 'D').

Slowly push down on the clip (as shown in Figure 5b - 'B') until it is lined up with the bottom edge of the socket (Figure 5b - 'C').

Latch clip onto socket tab (Figure 5b - 'D').
Caution: Take care to not scrape the motherboard underneath the 370-pin socket attach tabs.
Connect the integrated fan power cable to the motherboard connector.
Power on the system just long enough to verify that the processor fan operates.

Figure 5a: Step 1 of Boxed
Pentium® III Processor FC-PGA Install
Figure 5b: Step 2 of Boxed
Pentium® III Processor FC-PGA Install

Before removing the processor, consider removing the motherboard from the chassis.

Pentium® III processor removal steps for metal heat sink clip:

Unplug the fan power cable from the motherboard's connector.
Follow installation steps 5-10 in reverse order.
Use a #1, small flathead screwdriver to unlatch the integrated clip from the socket's tab nearest the fan cable.
Insert screwdriver into upper clip slot. Push down on the clip and simultaneously rotate the screwdriver towards the fan heat sink (see Figure 5b ).
After the heat sink clip is free, slowly lift the fan heat sink straight up and away from the socket and the processor.
Raise the handle of the 370-pin socket, and then carefully remove the processor from the socket.
Caution: Make sure to not bend any of the processor pins.

Pentium® III Processor installation instructions for the plastic heat sink clip:

Raise the handle of the 370-pin socket.
Carefully install the processor into the 370-pin socket making sure that none of the pins are bent.
Close the handle of the socket (A). See Fig. 6a.
Align the fan heat sink clip to the socket as shown in Fig. 6a. Make sure to align the pin on the heat sink clip (B) to the hole in the fan heat sink.
Align the pin hole (C) with the PGA370 mark (D) on the socket. With the clip lever in the up position, install the fan heat sink on the processor.
Make sure both sides of the clip (E) are securely fastened to the socket tabs (F). Close the clip lever.
Note: Be careful not the damage the thermal interface material when installing the heat sink onto the processor.
Snap the fan on the heat sink as shown in Figure 6b.
Connect the integrated fan power cable to the motherboard connector (G).
Power on the system just long enough to verify that the processor fan operates.

Figure 6a: Step 1 of the Installation of the FC-PGA
Boxed Pentium® III Processor at 1 GHz

Figure 6b : Step 2 of the Installation of the Boxed FC-PGA Pentium® III Processor at 1 GHz
Figure 6c: Removal of the Boxed FC-PGA Pentium® III Processor at 1 GHz

IMPORTANT NOTE: If the fan is attached incorrectly, it may unlatch itself at a later time from normal jarring of the computer. If the fan detaches from the heat sink, the processor may be permanently damaged.

Please refer to figure 7a and 7b for the proper fan orientation. Notice the position of the Intel hologram and fan cable relative to the heat sink clip. Figure 1 is the incorrect fan orientation and figure 2 is the proper fan orientation. Furthermore, please make sure the fan is securely fastened to the heat sink by firmly pulling on the fan.

Figure 7(a) shows the incorrect orientation of the heat sink fan, while Figure 7(b) shows the correct orientation of heat sink and fan.

Before removing the processor, consider removing the motherboard from the chassis.

Pentium® III processor removal steps for plastic fan heat sink clip:

Pentium III processor removal steps:
Unplug the fan power cable from the motherboard's connector.

Remove the fan from the heat sink.

Open the heat sink clip lever.

Referring to Figure 6c, while holding onto the heat sink, slide (H) the heat sink (J) towards the socket tab (K) located on the cam lever side (L) of the PGA370 socket. The heat sink clip should pop free of the socket tab (K).

After the heat sink clip is free, slowly lift the fan heat sink straight up and away from the socket and the processor.

Raise the handle of the 370-pin socket, and then carefully remove the processor from the socket.
Caution: Make sure to not bend any of the processor pins.

الصور

في الرابط التالي
من [URL="https://www.intel.com/support/processors/pentiumiii/sb/CS-007568.htm"]هنا[/
URL]

ملاحظة :- النوع اللي أقصده هو أنتل بنتيوم 3 النوع اللي يشبه بنتيوم 4 مش الواقف!!!!
و السوكيت PGA370

أرجوا المساعده وشكراً مقدماً